Makita XST01Z 18V LXT® Lithium-Ion Brushless Cordless Oil-Impulse 3-Speed Impact Driver, Tool Only

Because of noise complaints, I switched from the DeWalt DCF887B to the oil impulse. I'm working on a large renovation project that necessitated the installation of over 10,000 self-tapping screws into 18 gauge steel studs and 16 gauge tracks / ledgers. When I used the DeWalt, several neighbors complained about the noise, which is understandable given that the steel frame amplifies the volume of the already loud impact, which literally echoed throughout the neighborhood. Listening to it for weeks on end is probably a little tedious. br>br>The oil impulse has subsided significantly - It's easily 20 decibels quieter. While there is a noticeable reduction in sound when driving large fasteners (e. g. lag bolts) into wood, when driving self tapping screws into light gauge metal, the reduction is much greater. The Makita is so quiet that I can work until the wee hours of the morning without disturbing anyone. br>br>Another difference I noticed between the oil impact and the DeWalt is that the Makita oil impact has less torque / feedback transmitted to the hand. Impact drivers don't have much feedback (compared to a drill, for example), but the Makita oil impact has even less. It took some time for me to get used to the lack of feedback and figure out when to let off the trigger to avoid stripping. br>br>My only gripe is that the Makita's battery life is a little shorter than the DeWalt's; I assume this is due to the hydraulic action wasting more energy? In any case, this is a fantastic driver.

Lorelei Patterson

| Mar 20, 2021

Made in Japan, it's a high-quality, powerful Makita impact that comes with a learning curve because it's so quiet that you'll break and strip screws before you realize it. When I'm doing carpentry, I only use it on medium or low. br>br> According to what I've read, the soft impact mechanism has a rate of decay. I'm not sure if that's 200 or 2 million hours. However, I do not use it on a daily basis; instead, I rely on the less expensive sure compact impacts. br>br>It's also temperature sensitive, because the viscosity of the fluid in the soft impact changes with temperature. It appears that Makita advises against using it in temperatures below 40 degrees Fahrenheit. It has the potential to harm itself.

Joyce Conley

| Jul 31, 2021

I regret not purchasing it earlier. I really like it because I'm a professional contractor and my tools get abused. This one has taken the place of my Makita Impact. Even after a new brush tune up, it had begun to show signs of wear. I decided to pay the extra for this because the old one was extremely noisy. Especially when it comes to laying out decks. To get a little P, I used to rely on the drill driver. , I really like this one, it's powerful and quiet at the same time. The only regret I have is that I did not purchase it sooner. br>Well done, Makita!.

Colin Jefferson

| Jul 01, 2021

I'm talking about complete silence. Don't get me wrong: it's still an effective tool. You won't be able to use it in your apartment at 3 a. m. without annoying your neighbors, but it is quieter than I expected. br>br>The impulse has nearly the same driving power as a makita impact driver while being nearly as quiet. Indeed, the impulse action is so smooth that I had to double-check that I was using the correct bit. The thing seemed to be spinning uncontrollably.

Brantley Andrews

| Jul 25, 2021

This is a fantastic tool. From about two years ago (2013-2014), I used a Makita 18v LXT impact driver. 2014). It's extremely useful, but it's also extremely loud. It's gotten to the point where ear protection is required. This device is a LOT quieter than the previous one. Don't be fooled by decibel statistics; the difference is obvious when comparing the two. if you're looking for a relatively quiet impact driver That concludes the discussion. br>I believe it is even more powerful than the previous model. I was able to drive a 5" wood screw without stripping anything. br>I've also discovered that the 3-year plan is the most effective. When it comes to avoiding overdriving and stripping things out, having four torque settings is extremely helpful. br>This is a wonderful tool. In my opinion, it is a little too expensive, but that is what you get if you 'early-bird. ' adapt'. Makita, I appreciate your help.

Aniya BEVAN

| Apr 12, 2021

This is the best drill I've ever used, and it's ideal for anyone performing service calls or working in a busy home or office. The quiet part of the drill is more for the clients than for me (though it is definitely nice to work with if you are in a small area). br>br>Because torque and loudness appear to scale with speed, you could use the smallest speed required to drive the fastener if you wanted to be very quiet. The low torque numbers made me hesitant to purchase this drill. You must keep in mind that the torque is applied differently (constantly) and that it actually tightens faster than my other regular impacts. Drilling 1/2"x4" on a regular basis is not a problem for me. 5" lags into studs, and I've even put it to the test without any pre-treatment. drilling (which has no effect on the outcome) On paper, torque values do not correspond to real-world performance. In every way, this thing surpasses my standard impacts.

Mccoy Henderson

| Jun 11, 2021

After 5 years, I decided to purchase another. I'm a big Makita fan who's been buying their tools for years, and this little tool is fantastic, except it died after only three uses. I've been using it for 5 years, and I'm a GC, so I'm always using it. In comparison to the other impact drivers I own, it is extremely nice and quiet. But, and this is a big but, it died the night before yesterday. I tried a fully charged battery pack and the drill began to smoke, so I know it's toast. The battery worked fine on other tools, in case you're curious. This time, I spent $30 on Amazon to get a four-year coverage plan, which gives me an extra year and could save me $200 next time. If you're not a GC, it'll probably last you a long time, but beware of the price.

Christian PARRY

| Jul 08, 2021

The soft- The impact concept is brilliant, and I purchased it with trepidation, but I know Makita can work magic on occasion, and sure enough, I got lucky, because this thing is HILARIOUS. When it comes to fastening, the human skill is to find the best driver. Fastener contact is possible, and the soft impact allows you to fine-tune the ideal angle to drive and the amount of pressure (muscles of the hand and arm) required. This is a three-part series. but the drill remains the same- In a variety of applications, tip mode is a useful feature. I use that mode more frequently as I become more accustomed to it.

Georgia Dodson

| May 01, 2021