TOPGREENER Motion Switch, PIR Sensor with Ambient Light Level, Occupancy & Vacancy Modes, No Neutral, Ground Wire Required, 5A 360W LED/CFL, Single Pole, TDOS5-JM-W-2PCS, White, 2 Pack
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There is no dual-mode switch here it is only for single-mode Poles can only be used for poles.
This version of the TDOS 5 Having 2 black wires for power incoming or outgoing allows J to be used either way. It is necessary to have the green wire as the return wire in order to make the sensor work.
Motion sensors that require a neutral wire should be connected to the neutral wire It is recommended to use the TSOS5 If you are using W, choose TDOS5 With these switches, you will be able to control light on and off by pressing a button. The buttons will also have an auto-mode button, so they can work both manually and automatically.
There are no smart switches in this set.
Selected User Reviews For TOPGREENER Motion Switch, PIR Sensor with Ambient Light Level, Occupancy & Vacancy Modes, No Neutral, Ground Wire Required, 5A 360W LED/CFL, Single Pole, TDOS5-JM-W-2PCS, White, 2 Pack
It does not have all the features advertised. This item has the following two main problems In the event that the power is manually switched off by the switch, it will not automatically be turned on if someone enters the front door again within 5 minutes (I have not waited long enough to determine the exact time yet definitely at least 5 minutes). The instructions state there is a 5 second timeout, but that does not appear to apply here). Until the motion sensor reactivates the light, you MUST keep the light on and let it time out, and then let it turn off automatically. Do you think the design is defective or just bad? There is no reason why an automatic switch should not be able to be manually turned off when you leave a room and come back on as soon as motion is detected Not at all. It has not even been five minutes since then. This is priceless! 2) There is no option to set a time between 15 seconds and five Whatever the adjustment between the two settings on the dial between 15 seconds and 5 minutes is, there will always be 15 seconds and 5 minutes. The power should be turned off after 1 minute. With only 5 minutes to spare, we're stuck. There is a clear indication that the time can be adjusted between 15 seconds and 3 minutes in the instructions. Moreover, it does not specifically state that the setting is 15 seconds, 5 minutes, etc. Is this a faulty unit or could the instructions be sloppy? As a result, I am very disappointed with this product, as it does not actually do what it claims.
There is a light on as soon as I enter. There are 4 settings for duration and an adjustment for the motion trigger sensitivity in this camera. Although, the motion sensitivity can be too high, so the system will not shut off. It would be easier for me to wire them without a neutral as it is one less thing to contend with. As far as I can tell, it hasn't caused me any harm. In addition, you can use them as a standard light switch if you wish. It's a good price for the quality.
I installed all of them myself with a Philips and a flat head screwdriver. There are decent instructions and the installation takes just a few minutes. Since I want to use them in other places in my house, I will be adding more to my home. Several of these have been installed in my house for over three years without fail. They are highly recommended.
My goal was to install these in the pantry and a large walk-in closet You can find it in the It is common for family members to leave these lights on. Though I was concerned about some of the sensor impediments in those rooms, they still work well and even better than I I found the installation of the sensors to be easy and well-designed, and they both came with the shortest time setting that was perfect for my needs. It appears that adjusting the timing is a very simple task just take the cover off and use your fingers to adjust. However, be sure a system is right for your house before buying one. It is the 3rd unit of the series. In addition to the 3-wire, there is a 4-wire unit Buildings built after the late '00s (I believe) have 4-inch wire in the walls It is wired.
My motion detectors are configured to automatically turn off 10 minutes after motion detection was The default setting for my device is not to turn it If you normally switch off the bathroom fans when you leave, they don't always remove all the smell or humidity, but if you leave them on when you leave, you waste power running the fans for hours until someone notices that they are still running. This allows us to turn on the fans when we need to make a particular smell or create steam, and they will only run for a few minutes after we have departed.
Please see https//www. nbsp The two-packs are great. I got mine at a great price. My only concern is that the sensor may not turn on every time I enter the room, so I can't give them a five-star rating. The chance of this happening is probably one in ten. In addition, you can turn it off manually, go back in 30 seconds later, and then turn it on again. It is NOT necessary to use a neutral. Despite the fact that my house lacks a neutral wire, I was able to use the tools. Getting it up and running is a snap. My electrical expertise was limited to a few minutes per installation, and I completed them in 30 minutes It is a great thing that I no longer have to turn on the lights in their bathroom to use them.
The light comes on when you walk in the room and goes off for the rest of the time (and no motion is detected). It cannot function if it is not connected to ground. This makes me wonder why the motion sensor does not turn on the light very easily in a room with lots of light. Since I won't have to use the extra electricity during the day, I consider this to be a major win. However, the drawback is that the test mode turns off the light after 15 seconds of no motion, rather than 5 minutes like the next lowest setting. It would be great if the function could be set to 1 or 2 minutes. There is nothing fun about leaving a room and knowing the light will be on for 5 more minutes.
These switches are four of the ones I ordered. One of the faces came with the wrong faceplate, but in all they were mostly great. It has the effect of preventing the small plastic piece that is used to turn the light on/off from reaching far enough to In order to get it to work, I had to hack up a piece of tape and wedge it in. I'm pretty sure the other three are great as well, but I felt like it was pretty horrible to open a box and find.
You hit the nail on the head! It's nice to have these because you can turn them off whenever you leave the You will not have to worry about them turning on again until the time delay you set expires. With this feature, I can turn them off, park my car in the garage, and know that they are off! From now on, I won't be coming back. I love it!.