NOYITO 400W 15A Dual MOS Transistor Driving Module DC 5-36V FET Trigger Switch Board 0-20KHz PWM Electronic Switch Control DC Motor Speed Controller (Pack of 2)

NOYITO 400W 15A Dual MOS Transistor Driving Module DC 5-36V FET Trigger Switch Board 0-20KHz PWM Electronic Switch Control DC Motor Speed Controller (Pack of 2)

$ 6.99

Score By Feature

Based on 15 ratings

Giftable

9.08

Customer service

8.96

Value for money

8.87

Packaging

9.25

OveReview Final Score

How Our Score Is Calculated

Product Description

Designed to take advantage of powerful imported MOS transistors, with a high active power output, a lower resistance, a higher current, and a strong intensity.

Module provides strong output power the module can continuously supply 15A, 400W, which can satisfy most devices if the heat dissipation is enhanced. The module can provide a maximum output current of 30A at room temperature.

signal sources to trigger the MOS transistor module this can be triggered by the digital signal (DC3 3V-20V) and can be connected to the Windows port of a microcontroller, the PLC interface or the DC power.

Signals supported by PWM controller the PWM controller can access PWM signals, which can be supported perfectly at frequencies ranging from 0-20 kHz.

This motor control module can tolerate a wide input voltage range (DC 5-36v) and can be used for a wide range of high power equipment from motors, lights, LED lights to micro-pumps and solenoids. It can be programmed to control motor speed or light brightness.

Questions & Answers

Does this only effect the brightness of an LED light circuit on a 24VDC power bus and not affect the brightness of other circuits on that ?

I would think it is fine just based on the description you provided. When it is connected to the system, this needs to be taken into account.

What if we want to reverse the direction of the output sent to a device using this?

This doesn't mean that there isn't any Here are the The S-channel MOSFETs function similarly to NPN transistors, switching ground to an external device. One screw contact is for ground, and this is connected to the "source" pin of the FET. Two of the screw contacts are connected to the FET's "drain" pin, and this is the ground that is provided to the external device. The other two screw contacts (nearest the board edge) are simply connected to each other, serving as a pass-through. These screw terminals are merely a pass-through for connecting positive power to an external device, and they're not connected to anything on the circuit board. I actually do not use these screw terminals at all, but the LED on the board still glows when I switch it

What are the risks of replacing the onboard pot with a trimmer pot if it causes damage to the board (for embedding "set and forget" speed control)?

This method has not been tested by our engineers. In any case, based on past experience, it seems achievable. If you want to try it, you can.

Selected User Reviews For NOYITO 400W 15A Dual MOS Transistor Driving Module DC 5-36V FET Trigger Switch Board 0-20KHz PWM Electronic Switch Control DC Motor Speed Controller (Pack of 2)

I like these a lot, they work great

5/5

This is an excellent device for working with a dc pulsed electromagnet (PEMF). A 200 W magnet could not heat up the mosfet even though it was drawing 200W. It was the back voltage that caused the first unit to burn up, so I added a diode across the outputs and it's working like new now. If you buy the two-pack, the circuit boards are connected and although it has been scored, you will still have to score it a few more times with a razor or exact knife in order to be able to snap them apart. Exactly what I needed and the price was right.

Yosef Choi

| Aug 21, 2021

The motor of a small fountain pump was driven perfectly well with this

5/5

To control the number of revolutions per minute of a water fountain pump motor, I used this. I have connected it to an Arduino Nano pwm output. It seems to work fine. It can be hooked up with a power supply and ground. The only things you need are a power supply and ground.

Marlee MISTRY

| Mar 28, 2021

The work is done The fact that these have two separate drivers caught my attention some how

4/5

For twice as much current, they have two parallel wiring. As far as I can tell, they work as they should and are well-crafted.

Zhuri Barron

| Jul 02, 2021

That's a great tool! This works great with an Arduino and pulses electromagnets

5/5

Ruby Blackburn

| Aug 26, 2020

Has the potential to deliver what it says, but it isn't an A+ The Bridge

5/5

A product that does what it says it will do, but it is not an A+ Across the bridge.

Zaylee Ramsey

| Jan 05, 2021

This is a simple concept to implement

5/5

Whenever there is a need to switch a lot of DC current with logic level signalling, this is a great solution. Do they do strange things at night? (And did I mention they are very.

Melany Snider

| Jun 15, 2021

It is only possible to have a single pole

3/5

Despite having both + and - connections, there is no difference between the two Only one wire is switched, and that is the + wire. SINGLE POLE SINGLE THROW is the correct description.

Tadeo Medina

| Mar 10, 2021

Related Products For NOYITO 400W 15A Dual MOS Transistor Driving Module DC 5-36V FET Trigger Switch Board 0-20KHz PWM Electronic Switch Control DC Motor Speed Controller (Pack of 2)