Light of Mine 1/2" Inch 100% Cotton Flat Wick 6 Foot Roll for Paraffin Oil or Kerosene Based Lanterns and Oil Lamps with Genuine Red Stitch (1/2")
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
You'll need to take the wick throat of the lantern or lamp you're using into consideration. The wick comes out of this metal piece. You'll know what wick size to get by measuring the width of the piece. If the wick smokes and flickers, it's possible that it hasn't been soaked long enough in the oil to fully saturate it. There's also a chance you've exposed too much wick. Soak the wick for at least half an hour before using it. hour before lighting, and then slowly lower the wick until it no longer smokes. I hope this has been of assistance.
I'd send an email to the manufacturer about it. I believe so, but I've only used it with oil so far. In that application, it works perfectly.
Sorry, but I don't have the package in front of me and don't know where the wicks were made because they were too thick to use. I'm glad you value this!
Based on this information, I believe the 3/8" would be adequate.
Selected User Reviews For Light of Mine 1/2" Inch 100% Cotton Flat Wick 6 Foot Roll for Paraffin Oil or Kerosene Based Lanterns and Oil Lamps with Genuine Red Stitch (1/2")
These wicks performed the best across the board and required the least amount of trimming. They have the tightest weave of all the wicks I tested. To get the best results, soak them for a little longer at first. Work with a variety of fuels; 1 will always burn brightest, but paraffin oil (liquid paraffin with no scent) burns brightest and won't smoke if the wick is properly adjusted.
Two large lamps with antique Eagle burners are in my collection. There are no holes around the collar inside the chimney with these types of burners. br>I purchased a 7/8" wick, which was simple to install and appears to be a perfect fit. The flame, on the other hand, shrinks when the wick is fully soaked. It will not hold a bright flame no matter how far below the top of the burner I place it. br>I've read that running an oil lamp with the wick above the top of the burner disrupts the combustion process and uses the wick as fuel, but I can't get a good flame otherwise. br>As a result, I'll be looking for alternative wicks and possibly switching to Queen Anne-style burners. I'm not sure if it's due to the wick's quality or type, or if something else is at play. When I look up my problem on the internet, I can't find anything specific to it.
Several of the wicks in my oil lamps need to be replaced. When there is a power outage, I collect antique oil lamps and use them. I got this roll a few days ago and started replacing my wicks right away. When I do this, I always soak it, trim it, light it, and let it burn for a few minutes so there are no unpleasant surprises when it's time to use it. This wick burns quickly, very quickly, and then smokes like nothing I've ever seen when you blow it out; they all smoke to some extent, but this was insane. I'm not sure if I'll be able to return it once I've used a portion of the roll. However, I will not be purchasing it again. It would be great if you were in shape and loaded, but you're not! This is for you if all you want it to do is look useful, but if you want it to work, you'll have to look elsewhere. I'm going to give antiquelampsupplies. com a shot. com.
So I keep my three Dietz Jupiter 2500 lanterns burning 24 hours a day, seven days a week to keep my chickens warm in their coop in the Colorado mountains. I fill the three lanterns every day, trim the wicks, and clean the globes. I ordered this wick after my original wick became too short. This is not the same as the one that came with the lamp. The original wick is extremely thick, consisting of a single solid piece of cotton that is nearly twice as thick as the current wick. This wick resembles a flattened tube; it is not solid, and it is quite thin. And if I'm not careful, it'll fray when I cut it; I never had that problem with my old wick. And, for some reason, at least one lantern seems to go out every day, for reasons I don't understand. With my old wicks, I never had a problem. I'm not sure if it's burning the oil and the wick at the same time, but I'm not sure I'll order this one again; I'd rather spend a little more and get a good wick.
This wick material was purchased for a flint glass oil lamp that I discovered in an antique store. The lamp came with a chimney and a burner, but no wick. In the lamp, this wicking performs admirably. br>br>The only difference I've noticed is when the font's oil level is around half-full. Because the wick can't carry enough oil to sustain the flame when it's full, it burns very low. That, I believe, is due to the lamp's design rather than the fault. It has a slender profile that makes it elegant, but it is sensitive to oil levels because it lacks a shallow but broad font. The fount is quite deep, as you can see in the video, which is probably why I need to keep it at least half-filled. full.
Take a look around. On one side, the stitching is extremely poor, and the wick is asymmetrical, rendering it useless. I put it through its paces in two different Dietz Vestas. The wick raiser was ineffective because the wick kept bunching up inside; however, the original wicks worked perfectly. It's a shame that wicks that are several generations old or older perform better than these new ones. The quality is terrible. I've ordered from this seller three times and had to return the wicks each time due to quality issues. Look for a different seller.
I used this to make my own mini mason jar alcohol lamps to replace the store-bought "100-hour emergency" lamps we use during winter power outages. They always burn so filthy and unevenly, leaving soot all over the place and a filthy odor in the air. br>When this wick is placed in jars with an alcohol/distilled water mixture, it burns consistently, safely, and cleanly for a long time.
This 1/2 inch lantern wick has red stitching. This is not the case. I measured it with a micrometer and it's 17/32 inch, or approximately 13. 25 mm. 1/2 inch is also advertised for the lantern wick with purple stitching. It's also not the case. It was 7/16 inch, or about 11 inches, according to the micrometer. 25 mm. br>br>It's not a bad thing that neither of these wicks are 1/2 inch. If your lantern requires a 1/2-inch wick, try the red stitched wick first. You're done if it feeds well. If the red stitched wick isn't reliably feeding your lantern, try the purple stitched 1/2 inch wick. I have four Winged Wheel 400 lanterns, each of which requires 1/2-inch wicks. The red stitched wick is easily fed by three of them, but the purple stitched wick is required by the fourth lantern to properly feed it. br>br>UPDATE: br>br> I reduced my rating to four stars because I discovered a seller who sells genuine 1/2 inch wicks of exceptional quality. Wicks are available in a variety of sizes from Imperial Lighting Co. I purchased their 1/2 inch, and a micrometer confirms that it is in fact 1/2 inch. They fit all four of my Winged Wheel 400 lanterns perfectly.
Related Products For Light of Mine 1/2" Inch 100% Cotton Flat Wick 6 Foot Roll for Paraffin Oil or Kerosene Based Lanterns and Oil Lamps with Genuine Red Stitch (1/2")
