Moen 8912 Home 12-Inch Bathroom Grab Bar, Stainless Steel
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The bathroom was adorned with a tile shower bar. Our handyman installed it. As soon as he started, he drilled a hole in the masonry so the tile could not crack. To fix the screws, there are nuts mounted over the screws' ends. To minimize water seepage, he put silicone putty over screws near the flange.
Since your grab bar once rusted, I assume that you already have the correct holes for a replacement. This is only necessary if the stainless screws are long and tight in the correct diameter. In regards to the materials used in the shower walls, you did not specify them. A stud and appropriate tools are needed in order to attach new holes, including stainless steel mounting screws (you need to be careful not to rust the metal), as well as drill bits necessary to drill the holes. Drill bits that do not work on the tiles can give the tile trouble. It is a bit less of a problem with a fiberglass shower, unless you find out there needs to be more than one stud installed. Then, consider caulking the existing holes instead and using a vacuum-mounted grabbar. Your carpet or tile will not let vacuum units sit perfectly on the grout line, so avoid using them that way. For best results, you must try it by tugging the vacuum unit repeatedly while it's in use. Take care of the firm grip by detaching and reattaching the strap. You can do it in a few seconds if you want. A grip should not be weighed down until it is assessed as holding up properly. As I mentioned in a previous article, I own a shower stall under glass that holds these grips. I found they withstand heat quite well except when I remove them from the stall (hang them on a rack) and reinstall them. I test them before each application. Safe shopping is possible through Amazon. With Grip Bath andamp; Soak it up. Designed to handle a 17 inches flat surface. This is the same quantity of paper you need when you need it. After cleaning the wall, it becomes smoother and cleaner without appearing to have any residual soap scum. There are no rust concerns, and these can be readily moved around to a new tub or shower.
It measures 1 inches diameter. There is five inches in the body. My son ordered one with no installation date, therefore, I determined the circumference and dividing by 3 had to be done.
Since the shower wall will have some standard bolt holes and all of the bolt holes aren't lined, it is more important you drill new holes in the flange so it matches the bolts existing on the wall. The Moen 8912 bar has an attractive SS cover that hides screws from view.
Selected User Reviews For Moen 8912 Home 12-Inch Bathroom Grab Bar, Stainless Steel
There are two components to hardware. Hello, You can call ur brand gold- a name you know and one that you keep in touch with. The fact that a good hardware company should be complimented with cheap, foreign components has immense value. Don't let spending on management accounts decide your decisions; hire an authorized vendor with years of experience. You brand's value more than that. The two bars I bought were mine. I am pleased with both products to the best of my knowledge. Rap was included with the hardware. With two 12 (1. ) screws each bent (bent), it made it hard to get inside a 2/4 using the pilot hole, was coarse thread pitch (hard to get down even if the plane is straight), and it had head slots that were too shallow and rounded. It's impossible for them to keep their #2 Phillips intact without ripping up the head and cams out. As we were nearing victory, two of them flew right into my court, and I stopped to consider them. Using two Poper #2 heads and 12 proper-pitched stainless steel screws on a trip to ACE Hardware I received both bars installed in under an hour. You might be able to find other items which will be better at the Hardware shop including Hex or Torx heads. Do not trim these but take them to your favorite hardware store, buy one quality screw, install it by turning the whole lot t hey, thow all but one of the screws away, take it to your favorite hardware store, and buy some quality hardware to install them. Time will be saved as well as blood pressure will be lowered.
has the distinctive look of a Moen product, hence it deserves a Five-Star rating. Although I removed one star for misleading information, I will save it nonetheless. Secure Mount Anchors can be seen installing on the video. You can also see the anchors within the description. No secure mount anchors are included, only hardware for installation using the STUD. For places without stud and where this item would be useful, the Moen secure mount anchors are roughly $20 or more. If I had to place stud orders here, I would recommend this product. In reality, I think he would be deceived by the ads shown here.
They were indeed mounted there without studs in this video I viewed on the attached webpage. I don't know when that has happened since pleeeeeze doesn't. It is not safe at all to take any of these steps. Buy stud lengths so that you can connect them to your computer. In addition, rails that are short like the 12 should be vertical with the stud being made up of the vertical and horizontal parts. There may be others that do not add a wall stud size of 16" (standard unit spacing), since an inclined platform is ideal for putting the tub when it's sitting in place, and standing when it's off. These are quite strong, but unlikely be strong enough, nor are they strong enough for an adult to sit on a throne. The good news is that ups don't always fall as they do. Most people who need to stand can probably be found carrying bags. However, there has been an increase. My entry point is vertically sloped, so as to hold on for some time and for stabilization when entering the tub as well as reaching for the longer rail, which, to my eyes, is slanted as seen above. screws were far easier than those that came with nickel plates. There isn't anything wrong with these and they will last out this home without costing a lot of money and will be very useful by almost any member of the family, not just elderly. I was very pleased with the purchase, its strongness and the mere installation took minutes with my cordless driver. This product will do wonders when heated in the bath. Do something about it yples!.
RAVE! BOY!! An ADA-rated grab bar produced by the industry. Having built and installed many such units in nursing homes, I have an idea of what types of renovations I need to carry out. My wife mentioned that she needed a Bath for Master Bath, so I thought, "OK. ". I told him: "It's over". Are you ready to move on next step? Investing in reverse mortgages or life insurance with Tom Selleck, Alex Trebek or even John Selleck, these are great ways to start your business. What is the diameter of a ould be catheter? is diabetic?? Is it possible to walk into my in bathtub? Can't get up after falling I fall, and I can't get up? The next stop is this. This article talks about the geisha. When convincingly reassured, he stated he was merely providing balance in the midst of her horrifying raptor-like nature. My act was like a shower of redbirds. . . It is safe for now to breathe again.
Yay!.
As we have elderly parents who reside in our garage and live on the steps leading from our house, they found this helpful to their safety. There is great detail written in the instructions regarding the proper installation of long screws into stud holes. For this project, I suggest drilling just one hole in each end and aligning them to the end of the nail first before marking and drilling down as far as four screws in. Doing this is easier for this type of project because none of these holes will bind over.
Disadvantages: The mounting options and the clear instructions make it easy to mount the stud. The grab bar is well made and it can be easily mounted on any wall without any hardware. There are several mounting options in this grabbar. Six screws are used to attach this to studs; this could pose a problem for those who need to mount on wallboard since they cannot mount on the existing ones. They need to be purchased separately for the wallboard installation. Stud ladders can also be mounted vertically or horizontally provided that a stud finder and height level are installed properly. Even though the instructions recommend a bit of 1/8", I had to use a bit of 9/64" and some silicone to seal it tight while using the drill all the way into my work tool. It will create a risk of stripping the head if you try to force the screw with your drill. Replace the screw after it has been removed. For a smaller, narrower hole, pass the piece in and out two or three times. Install the grab bar using all pilot holes and make sure they are all centered. Moreover, your drill will crash into your grab bar because it needs an extension for its screw driver attachment. The installation was smoothly done. Security and design of the grab bar make it attractive and attractive to use.
Your health is best served by safe hospitals and a good investment. While our bathrooms were being renovated, these were installed in our bathroom. After much consideration, it was the best thing we could have possibly done. If you're having some dizziness problems or if you can't feel right from getting in the shower or get in line with the toilet, these are just a safety net that can help. In order to avoid slipping and to prevent hospitalization, we install these mats on pine panels. These mats are sturdy and keep us safe. A certain size fits them better than another size that I didn't know I really needed. Even though we have not had ts in most homes yet, they came as they thought they would. My husband suffers from seizure disorder and falls in the bathroom and the ts are strong enough that he has the strength to grab and ts. We did not receive any complaints about the product.
Related Products For Moen 8912 Home 12-Inch Bathroom Grab Bar, Stainless Steel
