Little Bear T7 Vacumn Tube Mini Phono Stage RIAA MM Turntable Preamp & HiFi Tube Pre-Amplifier (Black)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
This small preamplifier does not produce noise, and with a better tube, a smooth sound can be achieved. br>It's a nice piece of equipment for a reasonable price.
Most likely, as long as it's a decent player that isn't susceptible to external noise, such as from household appliances, that noise will be amplified along with the desired sound.
I'm going to tell you about my experience. I've got a Technics SL- Q200 and I placed an order for a ground cable. On both ends of the Little Bear's ground cables, which resemble roach clips, are roach clips. I used roached clipping on the Technics ground cable. The ground was solved by inserting a small screw into the hole of the Little Bear ground and roach clipping it. You can improve articulation and sound quality by replacing the left tube with a Jan GE 5654W tube. It was a little noisy with two 6J1. To operate on the right slot from the front, it will still require the 6J1 tube provided. It should work fine when connected to an aux input, but keep in mind that grounding is required.
I had to look this amp up, and it really depends on what you're going to use it for, like boosting your headphones with the 3. 5 mm headphone jack, but RCA output jacks must be converted to 3. To feed your headphones, you'll need a 5 mm cable. You'll need to convert the RCA jacks and use the aux 3 if you're using it to boost the line in to the ad18. It will not work passing digital through a 5 mm input because it is only good for two channel analog stereo.
Selected User Reviews For Little Bear T7 Vacumn Tube Mini Phono Stage RIAA MM Turntable Preamp & HiFi Tube Pre-Amplifier (Black)
I'm going to keep it short and sweet, with a few pro tips thrown in for good measure.
1. Take a look at the reviews and ignore the naysayers.
2. Upgrade your tubes by purchasing them. Don't stress about the research; Amazon recommends purchasing them from the "frequently purchased with" section.
3. Do the following first before connecting this preamp to your turntable, flac player, or stand-alone speakers: Remove the screws on the front of the cabinet. A switch can be found on the inside. The GAIN switch is what you're looking for. It's on the highest setting. Gently push it away from you with a screwdriver or something similar. GAIN is set to LOW in this case. If you don't do this, you'll be perplexed and angry, and your ears will despise you.
4. Connect everything to the power source and turn it on. Note: Don't get too excited; these are tubes that must be warmed up. So, if you want a warm sound right away, give it about ten minutes. br>br>Having said that, I made these upgrades and adjustments, and this unit is fantastic for the price. Even on records that only have surface sound - In comparison to any pre-recorded music, they all sound incredible. Any turntable can have an amplifier built in. br>br>I can hear sounds that I couldn't hear before, such as guitar plucks, percussion, and even vocal breathing. amp. br>br>I'd recommend this if you don't want to spend a lot of money on something extravagant. It also appears to be attractive. If I find another turn table, I might upgrade to the next level. I'm a big fan of what you've done so far.
It accomplishes the task at hand. It's clear that this is a low-cost unit, but I'm not hearing any major issues. I find it amusing that they put LEDs inside the tube mounts to make them appear to glow. It appears to be cool, at the very least. It takes a few minutes to warm up like most tube devices before it starts working properly. Give it some time if it sounds dark or muddy to you; I usually turn it on ten minutes before I want to use it so I don't have to think about it. Remember that tubes are almost always a gimmick at this price point. You're more concerned with (visual) aesthetics than with anything else. br>br>However, there is one major point to consider. The circuit board is the only place where you can adjust the gain (see image). Unless you're feeding a very high-protein diet to a very high-protein diet to a very high-protein diet You must set the analog input to "low" (mine was set to "high"). If you're feeding a digital input (e. g. , a computer), you'll want to keep this in mind. It must be set to low (for digitizing vinyl) at all times. br>br>All modern records will distort badly if gain is set to a high value, even if - is used. Prior to the ADC, a gain of 20dB is applied.
CAREFULLY read all of the reviews. SO. br>I'll give you a condensed version of all of the reviews. br>The most important thing to remember about this unit is that it takes some time to warm up. Approximately ten minutes to get the best possible sound A SLIGHT hum can be heard when I first turn this unit on. The hum is very faint, but it goes away after about 5 minutes. Time limit: ten minutes So. Allow time for it to get warm. Peeps also recommended that you use G tubes instead of the stock ones. tubes that I put together It appears to be wonderful. I'm not sure what the stock tubes sound like, but I kept them in case something went wrong with these. That's what happens when they start off on the right foot. br>According to another reviewer, you should open up the unit. Reduce the hum by setting it to "low. " I tried to open the unit but couldn't get the board out for the life of me; fortunately, my setup didn't require me to make any changes. br>I'm using a Technics 1200MK5 turntable with a Sure M44-based cartridge. 7 needles in each cartridge a head shell from Technics I'm going to replace the needle with one that isn't used for scratching, but I don't have any other options. I'm a DJ, to be sure. Make the most of the resources available. The receiver in question is a Sony DN-XXXXXXXXXXXXXXXXXX 1030 br>In general, this product performs as expected. If you've made it this far, I hope you've found it useful. Take pleasure in it. Spending a lot of money on records is not a good idea. br>I wish you all the best.
It was fantastic to add the "little bear T7" sound! However, after only a few hours of use over the course of less than a week, the sound became clipped. Is it possible that the cartridge is producing too much signal after it has been "broken in"? Loud passages are clipped, whereas quiet passages sound good. There was no difference after I installed NOS tubes. As a result, I ordered a new LBT7 replacement. The box had been tampered with when it arrived. The new unit has the same sound as the old one. Is it a design flaw or a manufacturing flaw? On the product description, there is a gain control mentioned. Perhaps it should be mentioned in the user manual, along with instructions on how to adjust and use it. After some disassembly, I was able to locate the gain switch. The problem was solved by lowering the gain. Tip . Turn off the power and disconnect all connections before removing the front panel and accessing the switch with a bent paper clip. Put everything back together. reconnect.
Related Products For Little Bear T7 Vacumn Tube Mini Phono Stage RIAA MM Turntable Preamp & HiFi Tube Pre-Amplifier (Black)
