Shankly 5 Ton Capacity Bearing Pullers, Bearing Puller Set and Bearing Separator Kit

In order to separate a bearing from a spindle on a small lathe, I used this tool. In order to mount a bearing plate on my small press, I needed a Even though it will prove to be a less durable tooling than it is worth for its price, I think it is a reasonable value for its price. There are some images of the tooling to illustrate the size. *I'm using metric sizing for this tooling. A pair of M12 studs and nuts will fit the larger plate Among the smaller plates, the M10-sized ones are used A M10 nut and stud attach the uprights. Lastly, the uprights use a M10 bolt. The kit contains nuts that might need to be replaced, so if you buy the kit, you will at a minimum need to replace the nuts. The screws I received were so loose that when you screwed them onto the shafts you could clearly see them tilting as you screwed them on. I crossed my fingers and went for it, but it did not work. Under pressure, the nuts came off the shaft during my first attempt to use the bearing pullers, a fault that is 100% unacceptable in the case of All of them have been replaced. In fairness, while the issue of the uprights is being discussed, it was already missed opportunity. The threads of the smaller plate could have been upgraded to make them the same size, requiring one less In regards to the plates, the 3 and 2 inch sizes aren't quite right. The maximum opening of the large plate is 2 1/2 inches measured at the widest point of the curve with the plate totally open and the nuts flush with the tops of the studs. For the smaller plates, the maximum opening was measured at the widest point of the curve at 2 5/16, measured at the top of the studs and measured at the point where the nuts flush with the tops of the studs Pros It's not affordable for her- The nuts may need to be hardened, so you may need to spend an extra ten dollars. The use of this tool can be useful if you have to pull a little pulley on an occasion. It is not a production grade, but it is light duty.

Theodora Freeman

| Dec 03, 2020

During the repair of an a/c compressor, I used this device to remove a seized bearing. A picture of how the set up looked and how I pulled it off is included. As it turns out, I did grease the threads with cheap oil to reduce friction and apply more force to The outer frame of the pulley on the pulley was also cut off so I would be able to place.

Piper Bailey

| Sep 27, 2020

Over the years, it has been abused and used by me a lot. When I looked at the saw, I noticed movement in the arbor shaft, so I opened the saw up to find the rear arbor bearing The old armature shaft bearing had to be removed from the shaft so that the new bearing could seat. The "OTC" bears comparison with many other bearing separators I reviewed. As a result of reading the reviews of that tool, I was unable to justify the additional cost. Upon receiving the tool, I checked over the threads on each part. Each part appeared fine. After that, I greased them and assembled the separator. Snuggling up all the nuts, I removed the separator. Immediately after the shell of the old bearing was removed, the bearing was disassembled. I found that the tool was very adept at helping me with.

Makai Lehman

| Jun 08, 2021

attempted to pull the gears with borrowed 3 leg gear pullers, but they did not Last week, I finally bought a Shankly gear puller set. It has been a real pleasure using it. The portable projector is easy to use and easy to set up. As soon as the steering wheel fell off, I felt so relieved. Also know that I did not use a hand held wrench, but an impact gun. Shankly's gear puller set comes with a variety of length bolts and two different center pieces to adapt to a wide range of A great deal of care has gone into making it.

Alec Nolan

| May 31, 2021

I think that it offers a good value in terms of quality and assortment. The belt can be used on bearings as well as other mechanical components, such as small to medium sized gears and pulleys. You will find a nice selection of adapters and extensions in the set, which is basically all you need to get most jobs Additionally, the case it comes in is nice and sturdy, much better than those that come with most of the It might strike a chord with some of you that you get what you pay for. I tend to believe that is true for a lot of things, but this tool set is an absolute We don't think you will regret buying it once you've tried it!.

Preston Frost

| Jul 22, 2020

As for the positives first It was easy to assemble, it removed a bearing from an arbor shaft with ease, and it was reasonably priced. *The negative The box was in good condition There was, however, an indentation in one corner of the tool case. Regardless of being wrapped in plastic, an instruction manual and foam cover were not included in the tool case. As a result of Amazon's quality control being AWOL, Shankly's quality control failed to detect a returned item and it either got repackaged or not checked. Although I found a website for Shankly, it had a date of expiration. That sounds interesting. There were no negatives to this review, so it would have been a five-star rating.

Iyla Young

| May 01, 2021

A decent set at an affordable price that should pretty much last as long as you don't abuse it. With pullers, you are able to achieve 5 tons really fast, so make sure you come up with ways to mitigate forces if you are really wrenching. Whenever possible, try heating the component or soaking the part for a long period in rust/corrosion fluid (not just WD40). When dealing with really stuck parts, do both. Finally, be sure to grease any threads and sliding parts you use with high-quality grease Oils and greases for pressure washers Pullers usually fail because of this, which is why they strip and, sometimes, break.

Joel Gates

| Aug 20, 2020

As a result of this kit, the bearings on the center differential shaft on my Subaru Outback were removed. With the smaller bearings easily removed, it removed the larger bearings as well. A small amount of space was required to grip the bearing, so it was helpful when something small had to be gripped. I should note In order to accommodate the larger bearing on the differential's center, a large 3-inch bearing was required An advanced auto rental place rented out a jaw gear puller. It is not possible to modify the bearing splitter in this kit so it opens wide enough for that, but perhaps a threaded rod can be added for that.

Landen RAHMAN

| Nov 25, 2020