SharkBite U2008-0000LFA 1/2 inch x 1/2 inch Brass Check Valve, Push-to-Connect, Copper, PEX, CPVC
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Hey, I see you've said it before - a check valve will reduce flow by at least a little. Please feel free to contact our technical support department if you need a flow chart for this product at 877-442-4233 The 700-800 range I wish you best of luck*, *br>
Greetings from The SharkBite U2016 There is no way to prevent water hammer with the 0000LFA. By preventing backflow and back-ups, backflow can be avoided It is water that is siphoned off. If you have any other questions or need further assistance, please do not hesitate to contact our Tech Support team by calling 1(877)700-5666. Thanks for your kind words.
I do not know why you would want to do that, you could do a union instead or increase the pressure. After all, it is a check valve. Before you do anything else, make sure the arrow is pointing in the direction of the flow.
Thank you for your interest in In addition to copper, CPVC, PEX and PE- cable, this connector also works with PE, PEX and PE- The RT pipeline. As long as the vinyl tubing adheres to ASTM F876 – If the tubing meets F877 standards, then it will fit We are happy to answer any further questions, so feel free to call our technical support The 700-800 range I wish you best of luck*, *br>
Selected User Reviews For SharkBite U2008-0000LFA 1/2 inch x 1/2 inch Brass Check Valve, Push-to-Connect, Copper, PEX, CPVC
The internal check valve on the 12 volt fresh water supply pump in my travel trailer fails after merely a few months, so I have to replace it time and time again. Each time the check valve fails, water fills the fresh water tank, which then overflows. The check valve on my pump wasn't working, so I did not want to replace it due to a bad pump. Originally, I purchased a threaded check valve to connect to the pump directly. However, the male and female threads were reversed, and the valve could not be connected to the pump. Although I could have replaced the plumbing, the Shark Bite check valve made the task so much easier. To connect the Sharkbite to the line, I just cut the line and pressed it into place. We will have to wait and see how long the pressure holds.
You have to do this in order to prevent the cold water from being sucked into the hot water line. Therefore, when you turn on the shower again, the water will be warm rather than There was a little white plastic cover on the water lines that was held in with four screws so I had pretty good access to the water lines. There was a little bit of a tight fit, but nothing too challenging. In order to make the overall length of the line to the shower the same as when you put this in, you will need to cut 3/4" from it. I think the entire process took about 15 minutes. A leak does not exist. It isn't necessary to be careful about orienting the pipes once this is applied. You can rotate the pipes after you have this applied. You will also find instructions on the Sharkbite website for how to remove it if you screw up and put it in backward.
It's hard to get clean water because the pressure is so bad. The flow of water has decreased dramatically. Now that the installation is complete, the water pressure is poor. There is a problem here that has to be resolved. It is rare for me to write either a negative or positive review, but this is something that can really mess up a project depending on where it is installed, so customers must understand that the water flow will be adversely affected. Make sure that you take into account that when installing it, it will work, but only in the right context.
After the check valve in my hot water recirculation pump deteriorated, it just turned to dust. I installed this valve in line and fixed hot water issues caused by no check valve in that line. Simple to install, just cut and prep, slide it in My brazing skills are limited but I think this cold solution works better since there is no risk of damaging the plastic inside the workpiece. It is a perfect solution to a problem that If I didn't find this valve, the other option would have been to install a new recirculation pump, which costs $450+. This pump is manufactured by Grundfos (the manufacturer). This is a pity, since it conveniently no longer sells that wearable part. Thanks.
I have an on-demand tankless water heater, and I mounted these on the water supply lines anywhere there is a valve mixing hot and cold water, preventing the cold higher pressure water from pushing into the hotter lower pressure It fixes the problem of hot and cold splashes during the shower. As a precaution, I also cover the hose bibs outside and the toilet supply lines to make sure no bacteria finds its way back into the.
A backflow preventer was installed on my RV black water tank flushing system to prevent backflow. While it had to be installed in a tricky spot, it went in quickly and easily on the first try. It is different from most press-to-fit connections, since this one did not leak, and can be easily removed. Although SharkBite connectors cost more than similar products, using them will save you time and money in the long run.
To prevent backflow in an open radiant heat system, I used this sharkbite product. It failed to hold back our radiant heat well and worked as well as any other sharkbite product. During days when the circulation pump was off, the hot water supply would return to the hot water supply through the radiant heating pipe, back through the pump, and into the main Hot water in our house was only hot enough to last four minutes during showers, and a full shower would last four minutes It would take 5, not 25, minutes to run out of hot water. It took me about 5 minutes to install this and it fixed the problem.
I installed the device in five minutes after turning on the switch. It's great to have these things. Installation was quick, taking a few minutes from turning off the water to cutting the pipe to inserting the device into the line. It worked like a charm. It was quite difficult to reach the pipe location, and fittings needed to be soldered in would have been a great deal of work. By using the unit, a hydronic heating system supplied by a regulator was prevented from experiencing back pressure. The product is great.
Related Products For SharkBite U2008-0000LFA 1/2 inch x 1/2 inch Brass Check Valve, Push-to-Connect, Copper, PEX, CPVC
