SolidWork Professional Hand Caulking Gun with Highest 24:1 Thrust Ratio | Caulk Gun for processing all 10oz Sealant and Adhesive Cartridges or Tubes | Drip-free Silicone Gun | Blue

The first is the newborn edition with a size of 25 and a weight of 18. As I wasn't sure whether one would be the best fit for my applications, I ended both cases. It appears they are almost identical, however there are a few differences that separate them. SolidWork does not weigh as heavily as Newborn (NB). If you are using a stationary handle, you will experience a slight bending in the upper, but this is not evident when using a front handle (NB). As for the piston, while it looks similar on NB it is made of grey colored steel (and grey steel spring). rust and one on SW, however. Due to the larger frame and weaker welded on the NB (the latter), the rotating caulk bed ends are riveted on SW. On SW, the mechanisms for pushing the rod have been adjusted, and nothing changes on NB. The NB is stocked with a tube end cutting blade, and the SW lacks it. When a metal rod punctures SW's seal, the lock is protected inside the handle grip. When compared to the NB's puncture rod, which sits along the side of the tube, it is even thinr and shorter. As an aside, it doesn't have much bead size, unless you go in a tube to get a massive bead size, it will not be able to reach a seal. NB requires 38 squeezes from the handle in order to fully pack its tube (16:)]. SW squeezes 23 times (18:1) on SW Based on NB 87 mm handling force, the NB sticks move the cylinder by 6 mm (14 mm). When a squeeze of SW 100 mm is applied over the surface of the handle (5:44), a little under four millimeters of movement will take place (25:34). There is a thrust ratio (1 p. Most of the time, both are fine choices, depending on how thick the tube is (thicker will generally move faster with SW). It is neither hard nor hard to find similar prices in either. The NBs are stamped in China and come in two types. There is a stamp on SW, but it looks like almost all mold work on SW. SW does not have a tube tip cutter and does not have a reliable seal rod puncture.

Anahi Nixon

| Dec 10, 2021

These guns give you the most bang for your buck. I might not be able to use all the caulk tubes before I run out -- - Nonetheless, the SolidWork Caulk Gun is, from what I can tell, a good product. There is one small flaw which makes it annoying. There are just a few details they forgot on their gun. There was no slot for cutting inside the handle using the tip cutter. It may take a long time to pry open a new tube when loading it with things for cutting. As soon as one would be placed at the handle, one would have been put there. In light of its poor rating, I would be giving it a 4. 5 out of 5, and ordering more.

Giovanni Walton

| Apr 16, 2021

I have been caulking old things for a few years as a DIYer - 20+ old things, since I wasn't a professional. After that, I decided that I was going to upgrade and have a caulking gun that was really effective and easy to use. When I realized my entire mortar repair tube had been emptied, I was amazed at how well I'd been able to empty it with minimal effort. Having never before used an automatic caulking gun, I am shocked at how advanced this technology is in caulking guns. In my opinion, this is essential if your caulking is done.

Vivian Hammond

| Dec 11, 2021

Caulking was hard enough work for me to achieve, so my memory is very weak. This was many years ago, and my caulking gun from Home Depot was the least expensive we had available. My ability to extract anything in the tube was inadequate with all the strength it required. When a person needs a house repair, they can use a caulking gun. I had one recently to fix a faulty wall. The SolidWork caulking gun appeared in my Amazon search. There were certainly less expensive caulking guns, but with little hand work it was more the case from the more than few reviews I had read. Since I received my order and successfully used it, I can tell you how simple it was to use, in fact I was amazed. It was not easy to work around a punctured seal, so that I did not have perfect lines, since caulking is not one of my strong suits, although I could squeeze it. Despite not really wanting a caulking gun once before, I would have bought one from SolidWork. is easy to use and it makes caulking looks long-lasting.

Iris Holder

| May 07, 2021

Pros: In a tough case it is highly constructed, packaged nicely, and contains solid construction. There is not much movement and the puncture needle will not bend if at all. It is firmly seated in place.

Cons: I might have a dud, I don't know if I just got one. Every time I squeeze the grip to loosen the caulking, I get a clacking sound. rotate hard; The bike is stiff. The problem is that to stop the caulk from flowing, the rear lever must be depressurized. The video automatically stops, but not; You need to keep going unless you press down on the rear lever (sometimes unpleasant). You may find that the fluid always keeps rushing out once you press the lever. If you have not kept up with it, you are failing.

Skylar Fernandez

| Nov 22, 2021

It functions extremely well and does not cause an accident (although the puncture tool and tool of the hole are less than 3 inches long. ), but I find it is necessary to use a other gun's puncture tool (wire) or even wire to punch through the foil. In addition to my other caulk guns, they all use four inch puncture tools. While there is no cut off hole for tips on this gun, it doesn't matter to me as I prefer my utility knife for the job. When used properly, this gun makes a pleasant noise thanks to its ease of application and accuracy. A thick tip or broad tip can be needed in adhesive applications, and it must be easy to dispensing on.

Elisha Wiley

| Feb 02, 2022

This is dripless but not straight. Since I paid $30 for this calk gun, I thought that I would have another chance next time. As a result, I did not come away satisfied with this product. excellent mechanisms, but it does not seem like it is drip-free. There was no stopping calk would not stop running out! When my project was finished and I began wiping the access area after wiping several more paper towels, there was an absolute mess. Please bear with me, SolidWork. The product is very good if you drip it away.

Marleigh ALLAN

| Apr 09, 2021

As a child, I was intimidated by caulk guns as I could not work one at a time. Since I am allergic to firearms, I bought toothpaste tubes instead. I had trouble with the ones available from big box stores. I did not feel the performance would be accurate or strong enough in the hand. You are not the same with this one. Light and tough at the same time. As long as you continue to use the caulk, you'll only have to release it when you finish. After a few practices, I discovered that this became a really smooth and enjoyable tool. Having this is one of the best purchases i have ever made! Although I have to admit that I am a little skeptical to the idea of not having tip covers for the large caulk tubes. Is that part of our sense of beings or of questions about our place in life??.

Jeremy Grimes

| Jan 29, 2022