Woodpeckers Precision Woodworking Tools SG-WP Saw Gauge and Alignment Tool
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It is true. The saw I have is the same as yours. You will probably find that the saw is rather out of adjustment when you start checking In order to get the saw to perform at its highest level, I had to attempt many different adjustments before I finally got it right. The adjustment of the trunion so that the saw blade aligns with the miter slot was a real pain in the buttocks. In many online woodworking forums, it has been discussed that the blade of the R4512 tends to point to the left as the saw is raised. While trying to address that issue, I spent many nights trying to figure out what I could do. I am not certain I was able to get it within the tolerance I set. It's a good thing I rarely have to cut through thick material to require an almost full blade height, so I don't have to worry about that. Another adjustment I found difficult was adjusting the riving knife. I am a fan of the Freud LM74R010 10-inch riving knife. (I have tried many blades, and this one slices cleanly and seems to have reduced saw stress.) I use this saw blade almost exclusively for all cuts (it's narrow kerf ensures a clean cut, and the saw seems less stressed). There is a problem because it is almost the same thickness as the riving knife, so if the knife is out of adjustment, the material will stick. I too had to wait a while to get it dialed It is so amazing how many adjustments are made There is a way to accomplish this, but I urge you to approach this task with an excessive amount This will be helpful to you. There is nothing to complain about the dial, since it's a quality item. I appreciate that the tool does not require a battery, as some other gizmos I have in my shop require batteries. It seems that the battery on one of them runs out every time I reach for it. Getting a grip on this tool is not something you do all the time, but it comes in handy when you need to make those minor Hope you have a good day!
It is not clear to me what the question Sorotos D. is asking. However, I will make every effort to give you the right answers. (The Woodpecker Saw Gauge that I own looks exactly like the one in the picture. This is I suppose what is known as the Woodpecker bar gauge since it has three parallel bars that are in the miter track. The first two will be small, then there will be one larger one that sits on top of them in the track on which the dial indicator will lay.
There is no way to do it. The miter saw is just a saw that cuts at a relatively Making a square cut is as easy as using a square and making trial cuts.
The website of the company states. All parts of the Woodpecker Saw Gauge are made in the U.S. There is only one imported part, the dial indicator.
Selected User Reviews For Woodpeckers Precision Woodworking Tools SG-WP Saw Gauge and Alignment Tool
Simple to use and well made, this gauge is a good choice. Depending on the saw, you can get a TS blade parallel to the miter slot fairly quickly (if used correctly). The fact that this is a woodworking tool was a welcome addition to my toolkit. I am more used to using machine tools than woodworking tools. It was a little surprising to find out that the surface of my 'high quality' fence was quite wavey, but overall this gauge helped me determine whether to install the fence in my TS or not. In the actual gauge there is a drop indicator type, and the plunger should be perpendicular to what's being measured in order to obtain correct measurements (not relative differences). Additionally, it is better to pull up the cannula tip slowly, and let it make contact with the item that you are measuring, than to drag it.
While I have this tool for my new Sawstop is anticipated to arrive next week, I couldn't wait to see just how dangerous my Kobalt jobsite saw was. When I opened the package, I noticed some of the bag protection was inside the screw. That wasn't a big deal, but it was quite annoying. I received it in great shape, no damage, obviously brand new and without a problem.
Now We now move on to the interesting part. The process went without a hitch for someone who has never experienced doing such a thing before. My Kobalt jobsite table saw has a miter slot that I measured from the blade to the miter slot before mounting the jig. According to the blade, it was "toe out," about 11/10" to the left of the blade. However, I think it is better toe in than toe out. In the end, I decided to measure the fence's distance from the miter slot. Every time I locked the fence down, it would have a huge difference. The irony is not lost on me. It is standard for these saws to lock down in the front as well as the back. What do you expect though? The quality of the product you buy is determined by the price. Here is the moral of this story I didn't realize my jobsite table saw was so dangerous until I used this tool! There wasn't a riving knife, so it would have been a real kicker A delivery machine is back in action! My thanks to Woodpecker, this is a tool I would have loved to have years.
I spent a great deal of money on something that I seldom used. This would be similar to paying your doctor to tell you how healthy you are. With my blade square to the miter slot as well as the fence, I know I'm operating correctly. Moreover, I learned that the face of the fence looks like a banana The middle part of the sentence was inserted This was not what I expected. While the cost of knowledge is often high, the cost of ignorance is even greater.
My intention was to align a new table saw I had purchased with the Woodpeckers Precision Woodworking Saw Gauge. I found it difficult to use and, although it is well-made, I found it hard to operate. To get consistent measurements, it is necessary to apply pressure to the rear bar. You have to be very precise when using it. The result is that it is challenging to use reliably, particularly when tearing down the blade from front to back. The product defeats its purpose and defeats the purpose of checking the alignment of the table saw with the measurements it produces. I feel like it should be a lot better at this price point. Despite what some people may think, I do not Additionally, I noticed that Woodpecker just released a new version of this product, which sounds like it has fixed these problems based on the description. There is a price difference between the two.
As a result, I received something that was clearly previously used and returned, with scuff marks on the rollers and dinged edges (see attached photo), as well as not accurate when in It is not possible to align the end of the metal piece holding the dial gauge with the table when it is put on the roller in the track of my Ridgid table saw. When it is still and when it is moving across the saw or whatever you are trying to make flush, you have to keep one end down. There will be significant measurement errors as a result. As a dial gauge, I expected one of high quality, but this one was a bit sticky when in It is the roller design that is the only clever thing about it, as I expect it to compensate for any uneven track width in the advertised way. Although rollers compensate for some other problems that introduce more error than track width, the rollers still fail to cover the other deficiencies. It would be recommended to get a well-rated dial gauge from Amazon, and mount it on a block of wood attached to the Microjig Zeroplay if you plan to use it for calibrating a table saw. This saw gauge from Woodpeckers will suit your needs at a fraction of the cost of this one. My dislike for the series is strong.
Having not used anything like this before, I was able to calibrate my new Grizzly table saw to 2/10,000th's of an inch in four minutes (and after I did it once, I could do it twice as fast). While reading articles about how to set up my new table saw manually, I realized that it was difficult for me to understand - In the end, this tool (plus the master plate) really made it easy for me to do, and with much better results than I could have obtained by eye. You can measure it or ball it up. In addition, I agree with previous posters - There is nothing less than a solid feel to it and it feels like a well-built item. Despite its simplicity, the tool is far from flimsy. It comes in a hard plastic case which is an excellent way to keep it safe (not everyone reports having the case, but the one I ordered came with the case and it's a must have to protect this precision tool). The tool was used for the first time by my father, who has been doing woodworking for decades, and he was amazed at how easy it was to set the table using the gauge and plate- he did woodworking for decades as well. In the interest of testing out his saws at home, he wants to borrow the saw and use measuring and eyeballing techniques to see how well they perform. This tool is great and I have no regrets at all about my purchase - I'm extremely pleased with it. If you are interested in doing precision work on any machine that can be calibrated, then I highly recommend this tool.
A quality tool like this is hard to find. The model is quite simple but very well thought out, precision machined, hard anodized, and well thought out. The laptop is protected by a fitted You might not need this if you're framing houses. However, if you're building furnishings or cabinets, you can avoid these problems. With it, you will be able to align your shop tools to ridiculous precisions. This must-have item is a necessity.
Related Products For Woodpeckers Precision Woodworking Tools SG-WP Saw Gauge and Alignment Tool
