SUNVIE Low Voltage Fastlock Wire Connectors for Landscape Lighting Path Lights 12-14 Gauge Cable Connector Work with Malibu Paradise Moonrays and Other Outdoor Lighting Brands (20 Pack)

When I ordered these, I had no idea what to expect, but they arrived quickly and exactly as described. I guess I didn't realize how small they are until now! LOLbr>I installed two 12VAC transformers, one in each location. I used 16/2 cord because the wire runs were short (about 60 feet) and I only had 5 3W fixtures on each. br>After digging small trenches alongside the path, I laid out the wire beside the trenches. I started at the farthest light in the line from the transformer and placed a box containing a light where I wanted each to go. This is a LOW VOLTAGE application, so it does not have to adhere to the same standards as regular household voltage applications as defined by the National Electric Code, NFPA-70. Also, because I live in Florida and these connectors will most likely be exposed to a wet and corrosive environment, I grabbed one of my squeeze-on connectors. electric anti-static tubes grease that is oxidizing Almost any hardware store will have this. It will protect the connections and bare conductors from corrosion and failure by coating them. These aren't meant to be used in the water. They don't have to be if they aren't. br>br>I opened the box and assembled the light, starting at the farthest light position, while installing the LED bulb I ordered separately. At the tail's end, I split the two conductors apart and stripped about 1/2" of insulation from each of them. I snipped the ends off two connectors and stuffed some anti-static into them. so that the ends were completely filled with oxidant grease I carefully split the 16/2 line and installed the taps (connections) on the main line; as the pin pierced the insulation and formed a seal around it, some grease squeezed out (very little), indicating that it was coated. Before sticking it into the connector, I slid the little ferrule type end over the stripped wire and slightly twisted the bare conductors until the insulation butted up against the post inside, and the wires went right through the grease between the center post and the connector's shell. I slid the threaded ferrule down the wire and tightened it into the connector while it was still in place. Voila! Done. There was a small amount of grease squeezed out of that end as well. I wiped my fingers on a rag and went on to the next one, and the next one, and so on. The small ferrule connects the bare conductors to the metal center post by pressing them against it. It does not hold the insulation and is not designed to do so. br>As I went along, I buried the 16/2, connectors, and remaining tail wire from each light in a small trench. br>I went inside for dinner after finishing and cleaning up. When it became dark, the photoeye turned on the lights. Perfect! Everything went off without a hitch. There are no issues. There are no issues. It is a good deal.

Quinn Kelley

| Jan 03, 2021

I ordered the 20 pack and received it the next day via Amazon Prime. The package arrived in excellent condition, and the SUNVIE Low Voltage Fastlock Wire Connectors for Landscape Lighting are of excellent quality and easy to use (and reuse), with simple and clear instructions. My project consisted entirely of new products, and the wire connector made connecting all of my lighting fixtures, including those that my wife requested I relocate after the initial installation, a breeze. (The only thing I would suggest is using clear silicone to seal the connection and make it completely weatherproof. ) I have reordered additional SUNVIE Low Voltage Fastlock Wire Connectors for additional lighting for my project. SUNVIE included a Thank You card for purchasing their product and on the I would strongly advise purchasing this product for a trouble-free landscape lighting connection.

Milani David

| Dec 09, 2021

One for the supply wire and one for the fixture leads, there are two connection points. Simple connections to the supply wire are made by tightening the fitting and piercing the cable with a barb. It should be fairly watertight at this point. The fixture's leads, on the other hand, are routed through a threaded compression fitting that does not compress the leads. There isn't a rubber compression gasket to be found. As a result, the inside connection is completely exposed to corrosion and ground water. You can either use silicone rubber to seal the fitting (which is a pain) or watertight wirenuts, which are widely available at Home Depot and other stores.

Kaison Ibarra

| Jun 18, 2021

Fill in the low voltage wire end with silicon, however. I was dreading having to deal with running lighting in my front yard, but these greatly reduced my anxiety. Simply screw into the main power line, feed low voltage light wire into the screw on bit, and tighten. Give it a tug to ensure it's secure, and you're done. However, when screwing in the wire from the low voltage light, it tends to twist the wire a little, so you must keep counter twisting the wire as you go to keep the wire jacket from twisting up. When you're finished, br>br>br> While the main wire (I used 12 gauge) appears to be watertight, the 18 gauge wire from the lights left a small gap. While it's probably fine, I just put a dab of silicon on the end of the wires before burying them, which should keep any moisture out. br>br>They're a little pricey, but I think they're worth it for the ease of assembly and the fact that they appear to be a long-lasting, reliable connector. We'll see if there are any problems after a year and a harsh cold winter (though I'm hoping it won't be harsh and cold, because it'll be bad enough with COVID in the air).

Juelz Shannon

| Jul 07, 2021

Lowest possible price! Connectors for lighting quickly Connecting your lights shouldn't take long. The only issue is that they aren't waterproof. Caulk, electrical grease, and/or electrical tape can all be used. Update: I've discovered that using electrical grease and tape before burying is the best and most cost-effective method.

Salem Walls

| Jan 25, 2021

True, they're simple to install, but replacing them isn't nearly as much fun because most of ours only lasted a single season. We weren't sure what was wrong, but after using a multimeter, we discovered that the conductor was corroding to the point of failure. I'd say they're still a good deal because they're not too expensive, but if you have connections in hard-to-reach places (like we do), it might be worth your time to do a manual connection with old-school wire nuts.

Ayan Carney

| Dec 07, 2021

I went ahead and bought two twenty-packs, and I'm glad I did. I was hesitant due to the cost, but when compared to other brands, these are the most affordable. The connection is extremely simple, and they work flawlessly with the 12 gauge lead wire that I used. They're made of high quality materials and should last for many years if you decide to move a connection. There's only a small pin hole in the wire that you can cover with electrical tape if you decide to move a connection. I would strongly suggest it.

Mckenzie Dawson

| Jul 02, 2021