PF WaterWorks PF0990 TankBRACE Support-Secure Toilet Tank-No Tools or Cutting Required, 1, White

This is a very misleading picture that is not adequately described. All the "adjustment" pieces except the one that screws on to the clip are 2" pieces - these do not screw on to the clip. Stack all the others against the inside of the small screw attached to the clip after you remove the 1" adjuster. Additionally, you need to turn them on the inside and use the protrusion in the center to stack them. It is insecure, and it is not strong. To use these other adjustments, you have to remove the 1" adjuster, which retains the screw attached to the clip, then press the two other parts into the tiny hole on After that, you hold your barely attached assembly with two hands to prevent it from falling apart - you need to hold it with two hands if it doesn't fall apart. The toilet tank wobbles as you slide between the wall and the wall. These adjustment pieces are only fitted to the inside of the small screw attached to the clip in the center. There is also that same small protrusion on the other adjustment pieces, which stack without being able to be screwed into anything. Even if a tank were to sag over time and rock even 1/16 of an inch forward - there would be problems As soon as the stacked pieces fall, they will all tumble I found the design to be awful. If your gap is 1", you will need to re-escape the gap by one". A thickness of 1 1/4 inches or more The truth is that you don't have to worry In this case, all parts are assembled with the only screw going into the clip and the other pieces that snap into place with a tiny protrusion on top of the 1" piece for a very strong My score is a 3/4 - and my height is 5'11 A 7/8" gap is required In spite of its seemingly worthless nature, this setup is not entirely useless Although very flimsy, the device does its job. It would have been easier to create the support if I had known what the problem would be for gaps of less than 1" in advance. It is highly unlikely that I would have ordered. It is a horrible design (for small gaps). You should be careful when buying.

Cassidy Kelly

| Oct 05, 2020

Next to sliced bread, this is a must-have! My only wish is that I had known about this tank bracket kit a long time br>It took 2 minutes to finish the installation from the time delivery arrived. two kits on two toilets, so in all honesty, I took about four minutes for each one! There have been several ways that I have tried to keep the tank from moving by wedgeing something between it and the wall, but eventually the wedge falls out and I don't realize there is a leak until it begins to leak! In addition, the design of this product ensures that it will remain in place for a long time to come! This bracket is an inexpensive, easy to install toilet tank bracket that I highly recommend. The kit will not work if the gap between the tank and wall is less than 1 1/8 inch, so I suggest measuring the gap before ordering the kit. It was less than an inch thick in the center of my toilet tank's back, but on its left and right sides it was more than 1 1/8 inches thick, so the kit was used. It is (0*0).

Amina Marshall

| Dec 13, 2020

There are several advantages to these toilet tank braces, including their high quality and ease of It consists of It is very easy to adjust the length of the brace to fit the gap between the toilet tank and the wall due to its block design that does not require cutting. I highly recommend this book.

Damian HOUGHTON

| Nov 20, 2020

There was no cutting spacers, glue, etc. I wish the instructions were a bit more clear as it took me a minute to understand how the pieces fit together, especially the end piece, but after I figured that out, it was fairly easy. It took me about an hour to space three different toilets that had been installed without proper support while the toilets were each installed in different locations from the wall, all of them are now very secure. Additionally, they do not appear to be that bad from above. I definitely want to buy again so that I can support my tanks properly in a fast manner.

Alena Mason

| Jan 29, 2021

It was 1 1/2 inches from the wall when the new toilet was installed. Even after putting shims under, it was still When I saw there were 5 bucks to be had, I thought I'd try it. were easy to install and took no more than three minutes. These don't need to be cut, which is a benefit. Depending on the need, each piece can be screwed in for greater thickness. Only the first piece needed to be replaced and it fit perfectly. Only the first piece could move. The fix is very cheap and these work great.

Skyla Gordon

| Sep 25, 2020

Located about two quarters of the way from the wall was my toilet bowl. As soon as I used it, it would begin to lean back. For bracketing the tank, a plumber suggested a 2 x 4 or something similar. Then you would need to attach the wall to it as well, which would be a huge mess. Easy to use, adjustable, simple to install, and easy to use, this product is the best option you can get. In addition to the hanger clips, there is also a variety of spacers in a pack. I love how easy it is and how well it works. I definitely recommend this product due to the fast shipping.

Dominick Barnes

| Dec 04, 2020

If there is a space behind your toilet tank and your wall, this will be a must-have. I found it to be very helpful. The toilet seats are against the wall, so they keep the toilet stable.

Lawrence Barron

| Dec 10, 2020

It is a clever idea, but if I had to buy it again I would just get the traditional L bracket that you cut to size. It was poorly executed since the disks didn't stay.

Anna Hanna

| Jan 13, 2021