10FT Heavy-Duty U Ring Shape Universal Garage Door Bottom Seals Rubber with Pre-drilled Aluminum Track Retainer Base Kit (10ft, Black)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I. What it is about This is a 25-inch wide mattress. In a severely unequal floor, the rubber seal will not magically fill in the gaps, as it is relatively stiff. As an additional step, there is the threshold product, which takes up more space in the floor.
There are approximately 3 inches in length. Some may think that's too much.
I would like to know the width of the aluminum retainer 1 Approximately 5/8 inch
In spite of the flange remaining on the garage door, I did not replace it. I set the three pieces of track (5 tracks I think) one by one with blue tapem in place with holes predrilled in them. After that, I drilled into the bottom of the garage door by drilling through the track. The track should be lined up to the farthest distance when facing the outside of the garage door, otherwise it might get caught up on the "lip" of the garage, where the garage door returns to the garage. In order to thread the rubber "T" flange into the aluminum track, you had to thread it through a hole. To make the slide, two people will have to pitch in with some soapy water. It takes about 10 seconds to slide one piece through the garage. Both ends should be trimmed of excess. With a narrow screw driver, you can slide back part of the rubber if it comes out while you are working on the track. As well as the upward tension, the garage opener needed to be adjusted downwards as well. You should have two knobs, one to control downward pressure and one to control upward tension on the main drive unit. Here's why you should adjust the tension upward. I had to turn my standard opener by a half turn to accomplish both tensions since the door was fairly heavy when installed. When opened it prefered to retract following the weight, but my heavy opener didn't want to pull back down due to the weight. Also, on the bottom of the garage door, I installed a rubber weather strip against the inside of the You can get a $20 gift card at Home Depot. There are two sided tapes. The thickness of one-fourth inch when installed. The material expands to about 1 inch thick when wet and If you have a double garage door, it may require two rolls. *br>Following this I am satisfied with my problems based on the price of the project. *br> *br>The only issue you have that I did not is the thickness of the Make sure it is the correct track because the scale is different. As long as there was enough room, we could install the track as well as My original body cavity is still intact, and I left the rubber piece on the flange in place.
Selected User Reviews For 10FT Heavy-Duty U Ring Shape Universal Garage Door Bottom Seals Rubber with Pre-drilled Aluminum Track Retainer Base Kit (10ft, Black)
install the track, I added additional holes at the ends of the aluminum track(s) to ensure greater rigidity, and I also pre-drilled the holes for each track hole To install and align the tracks as exact as possible, a small hole was drilled in the aluminum door. It was very easy to slide the rubber seal into the track with soapy water once the track had been installed. It is better to have the new seal contact the door trim and better seal the corner if I cut the excess seal material about 3/4 longer on each end. As of yet, the snows in Colorado haven't been able to blow under the door, so I'm no longer seeing light coming.
Delivered what was advertised, and had everything I would need (except the tools, of course, but I wouldn't have expected that anyway). I had a little warp in my garage door, so the extra tall seal helped to cover up a lot of flaws. Everything went smoothly, the installation process followed my expectations, and everything worked as it should. It was not difficult to get a perfect fit because both rails and gasket had excess material.
Followed the instructions and installed the tracks. There were numerous screws that stripped before going flush, and I had to use needle nose clamping pliers to remove them. When the garage door came on, it would drop, hit the ground, and then go back up again. Using the screws to adjust the tension on the door opener, I was unable to get it to work properly. After some more effort, I decided to remove the entire product and go back to a simple replacement seal that just uses a nail to attach. The garage door company I used to do this for me did it for I was told that this product would not work with wood garage doors. So far, it was a complete waste of money in my opinion.
It looks great and seals perfectly now that I have installed my new garage door seal. It was a DIY installation nobody helped me with it. To begin, I used blue tape to secure the seal retainer one by one. When I had to cut the last one a few inches, I used my grinder, but an ordinary hacksaw would also suffice. In the past, I left the rubber seal outside on my driveway so it could dry in the sun. I remember some people complained that it was difficult to slide the rubber down the whole way, especially if you were I made a spray bottle with a solution of dish soap and water. When I fed it on the track, I sprayed generously on the whole track and inside the rubber. I cut the rubber around 2 inches inside each end and tucked about 2 inches between each end, but everything went smoothly all the way except for the last foot which I had to pull a few inches at a time, then spray some soapy solution along the whole rubber one more time. The product should be recommended to anyone looking to replace their broken or worn bottom seal on a garage door.
Seals the door around the corners, but does not expand on those corners. It actually seems that I have more gaps now than I did before I replaced the There will be yet another product I have to purchase to seal the garage.
15 years after I installed my garage door, I decided it was time to replace the old, flattened and leaking door seal. The one on this page While drilling the screw holes, I followed the advice of other users and used masking tape to hold the sections in place. Furthermore, I cut 1/2" square x 3" heavy plastic strips to keep the sections of the garage door aligned when screwing them to the bottom. If the manufacturer could provide them with the package, it would be very useful. most difficult part of installing this vinyl was sliding the U-shaped piece of vinyl The strip should be shaped into the grooves. The first part of the track was able to be slid into the track by myself however, the next four feet required two people to slide into the Hurricane season is upon us now, so I'm all set!.
I had to install it in hell. As this item came in pieces, there were four of them, I had to start at one end of the rubber piece and pull it through. If I say pull, I mean that you need to get a hernia pulled. In order for the metal track to slide in, we had to soap up the metal with soap. DIFFICULT TO DO WITH ONE PERSON! To pull the rubber ends together, one must line them up, and the other must align them. This is a real pain in the rear. Since I was trying to fix my garage, I felt like I was being punished. The only reason I would have said "screw it!" is that I wasn't yet half way through the project. Seriously, this is terrible! As a more positive note, it does its job well and looks great. All I can say is, "Don't do it. ".
It was exactly what I had been looking for to fill a 30-lb gap in my garage door The year is My shop was a mess due to an old cement floor that had settled over time. Mice had been infesting my shop for a long time. Probably the easiest product to install, with an extra foot and a half, in case your door is a little off. My recommendation is to use this product.
Related Products For 10FT Heavy-Duty U Ring Shape Universal Garage Door Bottom Seals Rubber with Pre-drilled Aluminum Track Retainer Base Kit (10ft, Black)
