(4 PCS) DOT Approved 60W 4x6 Inch LED Headlights Rectangular Replacement H4651 H4652 H4656 H4666 H6545 Compatible with Peterbilt Kenworth Freightinger Ford Probe Oldsmobile Cutlass -Black

Oncoming traffic is not blinded by it, and the high beams are lit evenly. A photo of a high beam and a low beam has been added.

Paloma Phillips

| Jan 17, 2021

It is a great set of lights. You can hook them up if you figure out how. It didn't make sense to me at the time. If I try to purchase LED lights, I am only successful about 25% of the time. The success of this one comes as no surprise. On my Chevy W4500 (also known as an Isuzu NPR), I installed them. There are four lights included in this purchase. The new sealed beam halogens had already outperformed the old sealed beam halogens after just two of them were installed. Almost saved the other two lights for another truck, but in the end decided that what the heck, I went ahead with them You don't blind other people with their cutoff, so you don't flash them. Additionally, you have focused light in the right place. The driver does not have to worry about crappy lights that blind everyone, but do nothing to illuminate the area in front of the car. There was no problem with the fit. There was nothing I needed to change. I would like to mention There will be a need to modify the wiring on many vehicles. As this light (and most LED lights) are polarized, this effect can be observed. It is not the case with halogen lights. Consequently, a halogen light doesn't care about the polarity of the electrodes (which is positive or It is imperative to have the correct polarity for an LED to work. This means there are two leads -- a negative and a positive. You won't be able to light it up if you rotate them. There are many ways to wire the lights on a car. The halogens in Halogen lamps are not polarized, so they could perform this test. On my truck, for instance, the low beam wires are both + and + when the high beam is off. During low beam mode, the + and - buttons are on In the same way, high beams must be used. I had the lights constantly connected to ground and have the + wire switched on and off, while my lights did the opposite. With everything off, even when the lights were off and my ignition had been turned off, I still had +12V on all the wires to the lights. I had to hook them up with two relays and a fuse to get them to work.
I had no issues with the setup, other than the two hours it took to get everything connected.

Blaine Heath

| Jul 20, 2021

In a nutshell, Plug and Play was the answer the fire department needed for their fire engine. Installation is quick and easy. A new wiring is not required. After 30 minutes, the swap was complete. The product is high quality and fits in place perfectly without any modifications required.

Jazmin Cox

| Sep 20, 2020

It is a smidge too large to fit the silver retaining ring for my old headlights, but I still managed to make it work. I think I have found one of the best beam patterns for any LED that I have ever purchased. I think they outperform stock and give a much better light output then stock. In the cut off you'll see a pretty straight line with only a slight amount of haze, so you won't totally confuse drivers coming after you. There seems to be an insufficient amount of intensity in the low beams With just two low beams, the inner lights would not compensate for anything. I switched the low beams to the outer lights so that all four are high- and low-beams, which is more than enough to make up what they were lacking. As of now, I have only driven around town, and the lights are bright and clear, I will update when I get the chance to drive in the back country where I live. Regardless of my initial concerns, they have been well worth the gamble so far. I would recommend these to anyone that requires 4x6 lights in the future.

Forrest WHITTAKER

| Jul 28, 2020

I'm so happy I bought it. This is especially true considering the cost compared to lights sold at truckstops and on "Tractor Trailer Parts" sites. Previously, a friend of mine spent over $600 for similar lights for his truck, and I was jealous. This led me to try to find similar lights online. It was very easy to install these, however I had to use the wiring adapters that came with them so that they would work with high and low beams. I didn't have to wait too long. The lights are amazing and they are far brighter than any headlight I had on my car. With these lights they're so much brighter and whiter, and look like they're in a really neat pattern - not the type of glowing light that blinds other drivers, which seems to be popular right Having ordered another set, I just ordered a spare just in case I experience a problem with any It would have been nice if they were available for purchase separately, but there wasn't any evidence that they were, so I ordered another set to have.

Milan Graves

| Sep 04, 2020

This is a great light that works well in the oilfield. A multi-row LED light is much better than a dual row, which is much cheaper. During the day I can see every pothole and divot for over 100 In many cases, people believe they are on the bright side when they are actually on the low beam. You can only see 3 when it is bright, but on dark it is easy This is way better than most 400 yarders. These are just as good as the 1000 yarders. Thanks to your LED lights, I could work at night more easily. I also appreciated Kenworth or Peterbilt offering LED light bulbs.

Cayden Gentry

| Feb 24, 2021

I don't know the lumen value of these lights, but they are easily 5x more bright than stock without blinding drivers in front. About two months and 5,000 miles into the car's life, it appears that one of the lights has failed. Over the course of two nights of driving, the light was sometimes off and sometimes flickering, like a strobe light. In search of a solution, I decided to open up my grill and found that the bulb wiring harness had started to come loose. To ensure that the connector doesn't come apart again, I pushed it back together and secured it with a small zip tie. As I was worried that all the flickering had damaged the headlight, to my pleasure it was still in great shape and works perfectly as usual. To my extreme delight, I am happy with them and give them my 5 stars.

Sage Peterson

| Jan 30, 2021

My lights look great, but I'm having a hard time wiring them up for low/high. I could not get my lows to work when I put all four in. All of a sudden, they all were in high beam. There's also the option of lighting up just the 2 inner lights and nothing on the two outer lights. Therefore, I only have my stock lows and these for highs. I am not sure how to fix my lows so if anybody can help me I can send you the screenshot.

Anakin Conrad

| Oct 10, 2020