UVEX by Honeywell Bionic Face Shield with Clear Polycarbonate Visor (S8500)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
For the last four years, we have been using it to grind metal. An improved version of a run-up Here are the Adding a mill grinder to your machine.
The above question was answered for me, as I also tried the same solution. With an easy click I was able to fit the paper 95N type respirator with a With the removable rubber mask type, as the round pink 100P cartridges are lower profile, it fit with the 100P pink cartridges as well. There was perhaps a half inch or an inch gap between the filter and the We'll have to wait and see if the lens fogs up due to the exhaust shooting down. They would not fit in the organic compound cartridges used for solvents, since those hit the shield before being able to shut The test was performed with the shield at the lowest level.
My face shield stays right where I want it where I want it and covers my neck better than any other face shield I have used over the past fifteen years. There is a thick cushion on the head strap, which makes this one of the most comfortable head gears I have ever I have now replaced regular safety glasses with it as my primary face protection. A little regret that I didn't purchase it In my shop, I use it all the time. This is a very sturdy object.
A manual version of this one was created. I recommend you check out this link for a mask that's They will be delivered to me in 100 pieces. I GLORY IN GOOGLE SEARCH
Selected User Reviews For UVEX by Honeywell Bionic Face Shield with Clear Polycarbonate Visor (S8500)
My laugh is actually causing me to reach for the tissues when I see 1 and 2 star reviews and some who say that the plastic shield is "misty" and "opaque. " In addition, it is unclear. Can you be serious? Would you kindly share with me the following information? Two layers of protective coating cover the lens. There are two behind the lens, one on the inside, and one on the outside. Once they're removed, the lens will be clear as glass. It is not misty or opaque in any way. It has everything I need for what I'll use it for (grinding metal), and is cheap enough to toss when it has scratches or is hard to see through. A new lens is as little as $5 and I can simply buy one. Amazing item! It is exactly what I was looking for! Please note that. In order to demonstrate, I have taken pictures and posted them to this review of the lens with both protective covers, with one cover, and with no cover. You'll get the idea, but I believe they'll appear in reverse order.
It is probably not a good idea to operate dangerous machinery if you cannot figure this out.
As shown in the pictures, this is the "Clear" Polycarbonate visor, but it's not. Despite lying blatantly about what they are selling, as well as the quality of the product, it is substandard. The purpose of my purchase was to shield my face from water splashed on me while I worked. At that rate, I wager that it would be a failure. I am completely and utterly upset by my purchase, and I will be returning it today, the day after I received There will be no replacement from this company in the future and I will actively avoid using their products.
My first time using this product was in May of 2015 and I have used it quite a bit since then for grinding and sanding. It worked well for the purpose it served, and was comfortable to use. There is just one major complaint I have. It included a lot of hairline cracks at the bottom of the face shield when I first received it back in 2015. They seemed to have no effect on anything, but there were a few with a lot of small hairlines. It probably should have been sent back for a replacement after I made the mistake. Over time, all that small cracking has fragmented upward into the face mask and caused cracking. Although this mask would not leave my face without sweat, I would purchase it again and Please be aware of these small cracks when you receive it for the first time.
The intended behavior is achieved.
For a day, I wore this. So I tried it, since the Health Department reports that Corona virus is transmitted from hand to face. I had no idea how often we unconsciously touch our faces every day. My fingers had hit the shield as a result of this. The number of times I did it is lost to me. As far as the price is concerned, it's a good way to keep our hands off.
In the last few months, I have become interested in blacksmithing. After four years of living my life making bad decisions and slapping steel around without a mask, I no longer wished to carry on living it. It made me glad he was wearing this shield while he cut through a fire extinguisher last night, and he, too, was glad to have it on. Cut until the cut-through is complete - As a result of overuse, the discs are breaking apart The shield was used and one piece of it was hit right below his left eye. There wasn't much damage it could do other than a nice cut, but the shield prevented this. The shards and sparks did not strike him in the face. There are some weaknesses in this shield, but you can tighten it once you've done so. Also, you should remove the film from both sides of the mask so that it is easier to The purchase was great, and I would buy it again if the need arises.
For my science fiction video, I used it as a prop Films with a science fiction theme.