Superior Pump 93501 1/2-Horsepower Cast Iron Sewage Pump with Tethered Float Switch
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Yes, a 2" hookup or an adapter can be used to reduce the size if necessary. This pump will not only save you money, but it will also perform better than you might expect. Mine works perfectly, and I've saved a lot of money by using it.
The closer you are to the pump, the better; the further you are away from it, the harder it works.
Hello there,br>When using sewage pumps, drill a 1/8" or 3/16" hole in the discharge pipe above the discharge poet and below the check valve as an anti-airlock hole. br>If you have any additional questions, please contact us at 1-888-888-888. 800- 495- Mon - 9278 Between the hours of 8 a.m. and 8 p. am & br>Thank you for taking the time to read this at 5:00 p.m. central time.br>
The pump has a female threaded discharge port that is 2" in diameter.br>This is a standard pipe thread. The inside diameter of a pipe is measured, so if you're measuring 2-inch pipe, it'll be 2-inch inside diameter. If it's 1/4" outside, it's most likely a 2" pipe.br>An adapter will be required depending on the type of pipe you're using, such as PVC, ABS, steel, and so on, and can be found at any hardware or home improvement store. br>Thank you very much.
Selected User Reviews For Superior Pump 93501 1/2-Horsepower Cast Iron Sewage Pump with Tethered Float Switch
In August of 2015, I purchased this pump. My next-door neighbor, whose house is a carbon copy of mine and was built around the same time as mine, needed to replace his original sump pump, which had failed and flooded a large portion of his basement. My sump pump was in good working order, but I decided to replace it because his was failing at the same time. br>br>After some research, I came to the conclusion that this is a viable option. Regrettably, this was a poor investment. When my wife went to start a load of laundry around 9 a. m. on September 22, 2018, she discovered that our sump pump was overflowing. 30pm. The pump still didn't turn on after I bypassed the float switch. I took the pump out after opening the sump and undoing the pipe unions. I plugged the pump back in and the motor just hummed, as the impeller was free and not frozen. The impeller is not moving. The motor burned out after only a little more than three years of use. br>br>This pump only cycled a few times. Because I live on a hill, I don't have groundwater in my basement. It was only used when the laundry was finished, about 5 loads per week, or when the water softener needed to be regenerated. With a Kinetico system, it regenerates when it's needed and doesn't use much when it's not. br>br>I was extremely fortunate that my basement was not flooded; there was a lot of water under my stairs, where Christmas ornaments were stored in plastic bins. Some leaked behind the wall, but the carpet was quickly dried with a shop vac, causing no further damage.
This is my first sump pump replacement job, which takes an entire day, if not a whole weekend, to complete, and when you've completed all of the millimeter-accurate measurements, glued everything in place, and finally started to fill the pit with water, you'll discover that the float is too small to rise quickly enough before the water spills back into the toilet waste pipe; They could have designed a small "boat" float that could be attached under the existing float to give it more "height" for faster switch activation, but no such adjustable alternatives are included with this pump, so I wasted an entire weekend for nothing; Rather than wasting time and becoming frustrated, get a sewage waste pump with a large float that goes UP vertically.
I installed the pump without difficulty and have had no problems thus far. I would only recommend that the vendor include a note in the instructions stating that a vent hole must be drilled in the discharge pipe.
This pump was intended to replace a 3/4 HP pump that had become clogged. This was much lighter, and the capacity was very close to 3/4, which was more than enough for my normal use. br>br>Easy to drop into the well because it's so light and barely makes a sound when it runs. Keep in mind that when you install the pump floating switch in the well, it might not be in the best position. For example, if you use a standard-sized well and place the pump dead center, the switch will almost certainly be unable to move freely. As a result, you'll want to position the pump so that it's almost against the wall, directly across from the pump's float switch. This ensures that the switch has enough room to move and go in the direction it desires. It's critical! Never underestimate the amount of flexibility required by the pump switch. br>br>There is also no intake screen, despite what you may see in the photos or video of this product. When looking at the pump intake from the bottom, all you can see is a big 1. It's not a screen, but a 5 or 2 inch hole. This isn't a deal-breaker for me, but it's something to consider if it's a selling point for you.
It is both quiet and effective. It was necessary to shorten the float cord, but it was a simple process. I'm hoping it will last a long time. br>br>So far, Amazon shipping has been the only drawback. It could have been killed because it was not shipped in a box inside a box. It appeared to have survived, but only narrowly!br>br>If it fails, I will edit this review. So far, everything has gone well, and I'm very happy with the price and quality.
It has performed admirably as a pressure dosing pump thus far (a few months). My leach field is about 15 feet uphill and 150 feet away from my septic tank. Emptying the dosing tank (approximately 250 gallons) takes about two minutes.
The pump worked great for three months in a pump basin for our French drains outside, clearing several small rocks from the line. Pumps quickly through 90 feet of 2" PVC. The pump would occasionally fail to turn on, resulting in the basin overflowing with water. The float switch would trigger and activate the pump if I shook the pump or moved the power cords a little. Until a few days later, it wouldn't be an issue. I had passed the return period on Amazon, so I emailed the manufacturer, who responded within an hour. He demanded the serial numbers, stating that this was not normal for the pump, and fed-up with the situation. That same day, I ordered a new float switch. That response has me very impressed. I was expecting to have to buy a new pump, but instead I have a solution and will definitely recommend this product!.
The fact that the pump is in two pieces, each with its own plug, was never stated or shown in any of the pictures, and as you can see from the photos, they are designed to be plugged together before the whole thing is plugged into the wall. Unfortunately, in my case, this setup will not work. The "T" configuration of this pump plug was far too wide to fit through the PVC conduit pipe that runs from my sump basin to the receptacle. I eventually settled on a Zoeller M264 pump, which was ideal for my needs.
Related Products For Superior Pump 93501 1/2-Horsepower Cast Iron Sewage Pump with Tethered Float Switch
