BOSTITCH Coil Framing Nailer, Round Head, 1-1/2 to 3-1/4-Inch (N80CB-1)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
That's my guess. The nails are too short for the track, plus the heads on the roof nails are too large to fit through its holes. As the nail was driven through the material, the power of the N80 would blow it out. It is far more powerful to shoot a roof gun.
In addition to it being a strong nailer in the sense that it can drive nails into nearly anything, it holds a lot of nails, but you have no control over the depth at the gun. There are better nailers out there, but it's a "good" one
There's nothing wrong with this, it's a nailer for framing
Look at where the next nail is waiting to be fired in close proximity to the tip. At most, you can fit a 3 1/4" nail there. Mine has 3" inserted now, but more than that gap appears below. Depending on how much material you machine off, you might be able to fit 3 1/2" nails. However, you can always buy a gun that can accommodate longer nails at this point.
Selected User Reviews For BOSTITCH Coil Framing Nailer, Round Head, 1-1/2 to 3-1/4-Inch (N80CB-1)
owned several Bostitch guns over the years and have always been satisfied with them. They never looked back, no matter how bad the weather was or how much they were dropped. Even so, when it fell off my trailer (and fell approximately 2 feet), the tip broke and all pieces flew across the floor. Suddenly I find myself facing a $200 repair bill for a gun that was used just two days ago. As far as I can tell, they aren't made as often as.
Maintain it and it will last. The nails used for this were ring shanks. It worked like a charm. The instructions on how to change the trigger are very good. It has lasted for a long time. A total of 380 pickets were erected. A new day is beginning, but there is still a drop of oil left. As an owner of six Bostitch pneumatic products, I appreciate your efforts. Bostitch was not planned to be purchased, but because their price was so low and did not disappoint, they closed the deal.
A 12x24 building was constructed with this gun just a few minutes ago. It's an interesting read in general. I don't like how bulky it is. Powerful enough for nails up to 3 1/2 inches long. There was no jamming or misfiring even after rolling nails in it for several rolls. I wish it had a belt holder.
It was a witches' hammer. The heads of some offbrand nails in the 2" and under are about 1/16" too large when it comes to shrinking, so for nails in that size the shank diameter is right, but the degree is slightly off. They can be punched no problem, but it leaves the head with a razor edge that sticks to the wood (I'm looking at you, This unit sends three 13"s all day long, and it is not too heavy.
We were very pleased with the nailer's performance and enjoyed using it. As a result of reading the negative reviews of Chinese imports, I did buy the Bostitch brand nails. My nails can be bought at the following place Fortunately, this gun is shorter and more balanced than the gun that uses nails, so it is easier to hold. It is also good to have a large supply of nails.
The clipped head nailer I previously had was broken, so I decided to purchase this one. You will never run out of nails again if you have this head for so long instead of the clipped one! It's great that there are so many nails per coil. I've used the Hitachi nails with this nailer and it's fine. This nailer has not much to offer besides nails. The design is plain and simple, but it The framing nailer is a recommended product for any customer looking to replace their old.
This does not make me happy at all. I was planning on using it tomorrow but looks like I'll be driving nails in it!.
Nailer of high quality. It is easy to change out the.