Makita AF505 2" Brad Nailer, 18 Ga.
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It depends on how frequently you use it; for example, if you use it every day, maintenance may be required once a week. It's something you've done a lot of. Then do it on a monthly basis.
It doesn't have a muffler, but it's the quietest 18 gage nailer I've ever used in my 38 years of working in construction.
A narrower nose piece, in my opinion, is preferable, especially when nailing in tight corners. The larger nose piece, on the other hand, is very stable and effective, and I prefer it to Bostitch, Hitachi, and Porter-Cable nail guns based on overall construction. Cable.
Selected User Reviews For Makita AF505 2" Brad Nailer, 18 Ga.
This nailer has been in my possession for approximately six weeks. I bought it to finish a bathroom where I'm installing cedar boards at a 45-degree angle on all of the walls. The nailer worked fine with short wire brads, about an inch in length, but the 1 1/2 inch long nails seem to jam the Makita every 5 or 6 nails! Before I can reload the nail cartridge, close up the nailer, reconnect the air line, and fire another 5 or 6 nails, I have to disconnect the air hose (for safety), unload the nails, check for any dirt or dust (which there usually isn't), then reload the nail cartridge, close up the nailer, reconnect the air line, and repeat the process. Is it possible that the air pressure needs to be raised? I'm currently using 90 PSI, which is sufficient for driving the nails deep, but perhaps more air pressure is required? Anyway, if I could easily fix that problem, I'd give this product at least four out of five stars. As is, I'd give it about 2 1/2 stars. Update: I tried raising the air pressure to the maximum recommended by the tool, 116 PSI, but it had no effect. I decided to return it as defective and replace it with a Hitachi model. By the way, the Hitachi is the highest-rated unit in its class. Based on my personal experience and the reports of many others who have had the same failure mode as me, I can only advise you to avoid purchasing the Makita unit. I'm lowering my rating to one star now that I have more information. I'd give it a zero, but in order for your review to be published, you must give it at least one star.
But. I bought this a few weeks ago and used it for a few small jobs around the house, such as putting up trim and such. It worked great for about three weeks and I think I used it about five times. 6 times for a total of approximately 20 minutes Each session will last 30 minutes. and it suddenly stopped working, as if it wasn't building up any pressure; I tried the compressor with other guns, and they all worked fine; and I take great care of all of my belongings, cleaning and oiling them every time I used them. Anyway, I returned it and, with the exception of shipping, received a refund from Amazon. But I'm not sure I'll buy it again.
I recently bought a Makita MAC700 air compressor and needed a brad nailer to match. I needed a brad nailer for some of the finish work on a set of large basement shelves I was building. That was no problem for this nailer. It went in smoothly with the 2" Senco brads I used. Every brad went in perfectly, even though I was nailing into several layers of material ranging from pine to plywood. Following my shelf project, I went around my basement fixing some of the baseboard, and every nail went in without a hitch. Now I'm trying to come up with some other projects to use this with because it's so much fun!.
I've just finished laying down four miles of T With this gun, I was able to shoot G cedar without missing a beat. The other guy I was working with had a senco that had dry fired or double fired quite a few times; this one, on the other hand, worked flawlessly the entire time, and it's also very light and has a nice hook. The nose has a rubber protective tip that is slightly worn; I'm not sure if Makita sells replacements, but it still appears to have a lot of life left in it. I adore this weapon.
I spent $30 on a Harbor Freight brad nailer that I didn't need. After only a month of ownership and sparing use, it jammed or shot multiple brads. br>br>I chose this Makita because of its all-around capabilities. Other brands have used plastic parts and Makita's reputation for quality tools, whereas this model has an aluminum alloy body. I can confidently recommend this tool after using it extensively for more than six months. It's never jammed or fired multiple brads at the same time. I'm so impressed with how well it works that I'm going to buy Makita nailers in the future.
Makita products are good, and the customer service has always been good. I had Porter Cable and Bostitch brad nailers with similar capacities, but they couldn't compare to the Makita's performance. I started buying Makita power tools to replace other brands that were worn out or didn't work well, and I haven't been disappointed yet. Makita is known for its high-quality products, and this nailier is no exception.
I enjoy Makita products, but this one leaves me wanting more. It has a solid, heavy feel to it, which I like, but the nail set depth control is terrible. When nailing on curved moldings, even when the nail is fully set, the nail will often not be fully set, requiring me to go back and punch them in. Sigh. My old Porter Cable is missed, but that company has gone even further down the drain.
The square is rectangular. The product that was delivered was not the same as what was shown in the advertisement. The rectangular rubber part on the pin nailer that rests on the material in the picture is not the same as the one on the pin nailer. That's why I bought it in the first place. to avoid scuffing materials like crown molding on cabinets.
Related Products For Makita AF505 2" Brad Nailer, 18 Ga.
