Carter Products QR1000 Quick Release Band Saw Blade Tension Toggle

After that, I went out and bought a Carter quick release. Both are of a high standard. I started resawing and cutting veneer on occasion. I tensioned the band saw blade more than the manufacturer, Delta, recommended in order to achieve a better result. As a result, the wheel bearings were under more strain. I bought the Carter quick release because I kept forgetting to release the extra tension after I finished using the bandsaw. The good news is that it is more than I had anticipated. It not only relieves tension, but it also makes blade changes easier and maintains enough tension when released that I haven't had to reposition my fence to cut a straight line.

King HAYWARD

| Jan 12, 2021

This device allows you to release blade tension on your bandsaw, which will help the blade, tires, and bearings last longer. It also makes changing blades for whatever application is required a lot easier. It wasn't easy to install, but it wasn't too difficult either. I discovered the bolt holes overlapped the cast in webbing of the frame opposite the side of the tension device placement on a Cable 14" bandsaw (and a number of other similar makes, I suspect). I came up with a solution by slightly deviating from the original plan. Rotate the device counter-clockwise to change its location. In the frame's throat, where the tension mechanism is located, turn clockwise. I then drilled and tapped for 1/4-inch holes with great care. Instead of using the supplied hardware, I installed the tensioning device with short flat head screws that were just long enough to fully penetrate the casting but not quite long enough to reach the adjacent frame webbing. The supplied replacement M8 knurled head bolt, which was supposed to replace the tracking adjustment knob, did not fit this application, which is 5/16-inch in diameter. To fix the problem, I bought a thumbscrew. The stock tracking adjustment knob interferes with the tension release mechanism installation, but Carter anticipated this by providing a part, which will vary from manufacturer to manufacturer. Overall, I like this device; it's well-made and should last a long time.

Jameson READ

| Aug 04, 2021

Because it required drilling holes, I appreciated the inclusion of a drill bit. For 14" bandsaws, it appears to be fairly universal. I have the Porter Cable PCB330BS, but I had to drill an extra couple of holes because I didn't miss the cast iron webbing the first time, and I had to get a longer tracking knob (all thread bolt). It did come with one, but the thread was not compatible with my bandsaw. I now need to order custom blades because the 105" blade that previously fit is now too tight, and there is no way to loosen it to either the mid or high stop. My magic number is 106" blades, which I have to have custom made, making it difficult to get a new one in a hurry.

Benson Hubbard

| Apr 27, 2021

When used in conjunction with the Big Horn tension crank, it allows for much faster blade changes. When the saw isn't in use, the blade tension is released, which is a nice feature, though I usually forget to use it because I'm still getting used to having it. Disassembly and drilling two holes in the saw frame for the mounting bolts are required for installation, but the included drill bit makes this simple. One aspect of this mechanism that I find particularly appealing for my mid-life situation is the fact that it The carriage on the quick-change Delta bandsaw is from the 1990s. The tension screw is supported by a release mechanism that provides additional support for the screw point. As Louis Iturra points out in his excellent bandsaw catalog/handbook, saws from this era had a support pad on the frame misplaced in the casting, causing the tension screw point to rest only on the frame arm rather than the reinforcing pad. The misplaced pad is no longer a problem because the carriage now supports the tension screw point.

Rosa Palmer

| Nov 07, 2021

When you need to drill and tap holes in order to complete an installation, it's a difficult task. The instructions are adequate; they function properly, and I was able to complete the installation process without difficulty. I did have to get a drill and a tap, though. The unit is in good working order, and it appears that the machine will last longer now that it has been installed. I'm glad I went through with it, but I'm not sure I'd do it again. This kit will set you back around $100 and new tires will set you back about $20. I'm not sure if the money was well spent.

Nina Cervantes

| Apr 13, 2021

This is fantastic. I was a little hesitant to spend this much money to simply assist with blade changes, but I'm glad I did. I had a habit of leaving the shop with the blade sprung, partly because I didn't want to slack it by twisting the knob a hundred times. After looking at the quick thread knobs, I chose this one because it's extremely durable, made of solid materials, and the red knob serves as a reminder not to turn on the saw because the blade is also slack. You'll need to drill two holes through the cast iron. While drilling holes in your saw may seem intimidating, it's actually quite simple. They gave me a great metal drill bit that cut right through it. This is a mod that I have no regrets about.

Bria Fuentes

| May 02, 2021

Reduces the wear on the blade. As part of a full tune-up on my Ridgid 14002 Bandsaw, I installed it in about 30 minutes. This 14" bandsaw is being set up. It's super easy to use and makes installing a new bandsaw blade a breeze. It also extends the life of the blade and the tires, which would otherwise have the full tensioned blade on them unless you laboriously loosen the blade with the knob. This is a one-time deal. When it's time to cut wood, use the second fix. To tighten your grip, you can't reach too far up. This is something I should have done a long time ago because it is well worth the money. Thank you for making a high-quality product, Carter Products!.

Anahi Schultz

| Apr 28, 2021

Anyway, I'm very pleased with the results; it even easily tensions a 3/4 blade.

Valeria Stanton

| Nov 02, 2021