NEIKO 11106A Flap Disc | 40 Grit Aluminum Oxide Abrasive Wheel | 4.5" x 7/8-Inch | Flat Type #27| 10Pc | Sanding Disc

These disks offer excellent value for money when used at home. They came in handy when I needed to remove paint and rust from some severely weathered patio chairs. I went through four disks in total, one for each chair (approximately). Per chair, one hour of grinding time). I'm sure I'd have used at least two of the top-rated products. If I had chosen those, I would have gotten three high-quality disks. When was the last time you changed your clothes? A minute and a half more? With the savings, it appears to be a no-brainer. They're well-balanced, and if you're not careful, they'll tear your flesh just as easily as more expensive brands. That I can assure you of.

Kannon Clayton

| Jul 03, 2021

These wheels blend out welds quickly and efficiently without generating as much heat as a traditional grinding disk. I start with them and then add a 2" roloc to finish. I only wish they lasted a little longer, but they're comparable to other brands I've tried. I've bought them several times because I adore them.

Chaim Page

| Jun 26, 2021

To get these to work with my angle grinder, I needed a spacer. They'd be too loose on the shaft if it wasn't for that. They work fine once they're secured (perhaps it's just my grinder's fault)br> They quickly remove paint and shine the metal. I was working on a Viking floor jack that had seen better days. Re- It was part of the job to paint. These discs sped up the process of removing old paint and minor rust spots. br>These are items that I would buy again.

Paige Good

| Nov 10, 2021

I'm a new welder who does bodywork, so there's a lot of grinding involved. I was dissatisfied with the short lifespan of Home Depot's $10 flap disks. Based on reviews, I purchased these. Well! These last a lot longer and are extremely fast and smooth when it comes to removing welds. They can usually withstand 30 minutes of intermittent grinding (intermittent to avoid heating the metal). ) I believe they are a good deal at this price. After I finish the 2x10 packs I ordered, I'll order more.

John Ryan

| Aug 27, 2021

Good initial grab and a respectable quality. So far, there have been no strange vibrations, which is better than the cheap Harbor Freight ones. Approximately half the thickness - or less - compared to the standard Diablo flapdisks from Home Depot But, to be fair, each of these costs around $6.

Justice Benjamin

| Jan 11, 2021

These flaps don't bother me at all. They're a step up from the Freight-On-Demand-On-Demand-On-Demand the- Bay, and a notch below Yellow Brand in terms of abrasive layer thickness. Naturally, they don't last as long as the 10x more expensive ones. They're what I use to smooth and bevel mild steel edges, as well as remove weld slag. If you try to remove mill scale with them, they will quickly wear out. Even the most expensive discs, however, deteriorate quickly when used in this manner. I'm going to go out and get some more.

Ismael Eaton

| Jun 19, 2021

I've always bought the more expensive thicker flap discs because they appeared to last longer, but I'm always frustrated with their tendency to round out at the edge far before the rest of the pad wears, these are thinner, as reflected in the price, and they also round out at the edge but will still leave a flatter pad to work with, two of these Flapper disc will last longer and do a better job than one of the thicker flap discs. These sanding flap discs are excellent and I will continue to use them.

Layne Welch

| Jan 22, 2021

The flap wheels on these discs aren't the most durable. However, I've had a positive experience with them. When compared to similarly priced locally purchased wheels, these last nearly twice as long. They are in no way comparable to a high-end wheel that costs ten times as much. As a result, I'll keep purchasing and using them. These are a great buy due to their durability and low price.

Sean Adams

| May 21, 2021