Kreg Tool Company - Drawer Slide Jig with Cabinet Hardware Jig with Concealed Hinge Jig and Two 2" Face Clamps
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The jig, a bit, two drawer box supports, two clamps, and a handle/knob drilling guide were all included in the kit I purchased, and as I do custom installs and have to modify in the field, the entire kit has been helpful and accurate while being simple to adjust and set up on the job. I strongly suggest it!
That was the case with the one I had ordered.
Yes, it will work if you're talking about the drawer slide jig. This jig is used to align the drawer box and the slides so that they are level and functional. I hope this has been of assistance.
Selected User Reviews For Kreg Tool Company - Drawer Slide Jig with Cabinet Hardware Jig with Concealed Hinge Jig and Two 2" Face Clamps
The money spent was not well spent. Only the hardware jig is reviewed in this review. I haven't tried the other items yet, and based on my experience with the hardware jig, I'm not sure I'll use them. br>br>Setting up the jig takes some time. Then you'll need to figure out how to align everything. Then, according to your measurements, set up the jig. After that, you must measure each door/drawer and clamp the jig to the workpiece. You're ready to drill now. br>br>The cabinet pulls in my case were 3 3/4 inches long. This jig doesn't let you do that. As a result, half of the jig should be set for 3 1/2 and the other half should be set for 3 1/4. When you change from the left to the right door, you'll have to re-adjust your jig. It's difficult to put into words.
I gave up on using it and just used a square and pencil and installation was much more accurate and took less than 20 of the time
I%.
The sliders were held in place by those two, and the drawers were used to mount the sliders to the drawers. not good. I don't have a face frame, but I do have EU boxes. I secured them to the box's side with a clamp. It was easy to keep the sliders in place. When I put the drawer on them, however, it slipped. The clamps that come with the package are very small. They slipped and couldn't keep the box leveled no matter how hard I clamped them. To keep the box level and prevent them from slipping, I had to use screws. The money isn't worth it. I'm not sure if I'll be able to keep them.
I won't go into detail about how these all work because there are plenty of videos available. These can help save hours of shop time and improve accuracy in a variety of ways. The clamps are fantastic - I'd recommend them to anyone. I have two more corner clamps, as well as four more. It's a lot easier to align drawers and slides this way. This is fantastic. I would recommend this product to anyone who works with cabinets or boxes, particularly drawers. br>br>2/2020 Update - I can't believe how much time I'm saving on tedious drawer-making steps. I had to use these for a while before I realized how much faster and more accurately I was completing tasks.
This is a fantastic product concept, but the materials used to construct it appear to be of poor quality. par. The drill bit's sheath broke down on the fourth hole I drilled, and the drill bit began to wobble badly. I was able to repair the damaged hole and install the hinge, but my project has been halted because I had to return the product and place an order for a replacement. Because it took so long to drill out the hole (approximately 1 minute per hole), I suspect the drill bit was dull. br>I'm worried that the manufacturer will charge me for the return (hopefully not), because the product was used and it was mentioned on the return sheet that there would be a charge for used/returned parts. The damage was caused by a faulty product. br>What's even more disappointing is that I had to return the entire box when, if they had a return system in place, they could have simply replaced the cowel (drill bit included?).
Like most kreg stuff, this works well. The cabinet handle jig was my only gripe. Not the hole-drilling jig, but the handle-drilling jig. It only goes about 6 inches apart; we needed holes about 8 inches apart for some larger handles, and this wouldn't work. I had to purchase a different non-alcoholic beverage. For those drawers, I used a kreg jig. The other pieces worked fine; just make sure you measure your handles before purchasing to ensure that all of the parts will fit.
The hinge jig's screw holes aren't perfectly aligned. br>The 35mm hole is adequate and works well. With the stop ring, the depth is also good. br>The rest of the piece is excellent.
Making the process of cabinet construction a whole lot easier.
I've been looking into these jigs for a while but haven't had the opportunity or need to purchase them until now. However, after using the two jigs that were provided, I was able to make my kitchen cabinets and drawers look nice and clean with little or no effort in terms of measuring and mounting the holes. These jigs save a lot of time and aggravation by allowing you to center and align all of the mounting hardware.
Related Products For Kreg Tool Company - Drawer Slide Jig with Cabinet Hardware Jig with Concealed Hinge Jig and Two 2" Face Clamps
