KING PIECES Grommet Tool Kit Handheld Hole Punch Pliers Portable Grommet Hand Press Machine Manual Puncher w/ 500pcs Silver Grommets of 1/4 Inch (6mm)
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
We are sorry, but this cleaner cannot be used on fabrics and fleece of any kind. Normally, you would punch the material if it was too tough, but it may be pre-punched I am going to punch to see if it works.
In addition to works well with thin canvas rubber, and tarps, I have not used Block It or Tyvek house wrap. With LACUISINE Grommet Tool Kit, for example, they do work well. Despite the fact that there were different sizes of grommets, the only complaint was its lack of flexibility. Hole Punch Pliers work well better than hammer stiles when working with the hand held tool.
The grommet tool can be punched into different materials and at different thicknesses in general, it can punch into materials up to 2mm thick. Materials such as paper, thin cotton, and linen, as well as advertising banners, don't need to be pre-punched. Someone punched you. A convenient way to punch carpet is to use a punching machine. Thank you for submitting your question. The answer I provided should be helpful.
Selected User Reviews For KING PIECES Grommet Tool Kit Handheld Hole Punch Pliers Portable Grommet Hand Press Machine Manual Puncher w/ 500pcs Silver Grommets of 1/4 Inch (6mm)
Considering its size, and its durability, this hand held, hand press is a good buy. There are high-quality grommets on the belt. It is only the packaging that is a complaint for me A single word of instructions existed and a photo of the washers, grommets, and grommet tool did not appear. It is frustrating since the people who worked hard to make this grommet press and washers did a satisfactory I commend you for a job well done. Instructions and a list of the contents of the purchase should also be included in the email.
Throughout my life I have used grommets quite a bit. Forty years ago a punch was used to punch the hole or the canvas was cut as a X. In the next step, we took a die, attached the grommet to it, then stuck the die into After that, I used a setting tool and hammer to secure the grommet ring in place. Simpler than ever, I installed thirty tubes in just a few minutes with the help of Make sure the flat ring is placed on top of the magnet. Place the concave side of the flat ring on the magnet down, The grommet, therefore, sets into the concave or cone side of the ring as it sets.
Besides being well made and receiving it quickly, it was also exactly how I ordered it. The grommet set was the first time I used it, it took a bit to get used to, but it works great. As I was checking the grommet, I noticed that about 1/4 of it was not properly closed. Due to the fact that it was my first time trying, I assumed a user error had occurred. tried setting a second and it unfolded the same way as with the first. According to my examination of the tool, the top portion does not fully compress with the bottom portion. In the photo, it can be seen that the edge closest to the pivot mechanism does not close completely. Seeing that there are set screws, I decided it must not be aligned correctly. Upon removing the top, I saw that the set screw had been cross threaded and had become bent as well. A deeper inspection revealed that the barrels had been tack welded in place as well, in a spot where I was unable to grind off the weld and position them again. Therefore, now I own a tool that does the job sort of, but I won't use it The seller cannot be reached through any of the means I have tried. The possibility of this being a one-time problem piques my interest, but I'm not sure it is. Purchasing this tool at this point would not be a good decision. I received the replacement tool, but when I opened it, it was set up exactly as before. It is evident from the 2nd photo that the barrels are not lined up and they are also tack welded, which makes it impossible to adjust. As well as being bent and stripped, the top barrel set screw is bent and cracked.
In case of arthritis in your hands, you should not buy this. These were quite painful to use, so I didn't want to continue using them. It came without instructions, so there is no information available. Although the grommet pieces have a magnetic feature, it is still difficult to attach them to the unit. Due to its narrow shape, when the cloth is put in, the grommet sections are often pushed out of It is very difficult to cut through the cloth through a grommet and even after the grommet has been made the fabric is rarely removed. There is a lot of cloth left in the hole as a result. This is either how big a hole the product makes or how it is designed. Despite the fact that the plyers are heavy, the grommet maker appears to be poorly designed. AD2 I recommend.
My order was reordered, and I'm glad I did. A new order was placed after returning the old one. When washers do not come with the product, it is worthless.
You may pre-grommet your (1/4") grommet if you do the small amount of work If you punch (using the stapler-like punch), and ensure that you have only one bottom washer (they can nest together and look like only one), and then align carefully, then you can make dozens of grommets that are identical and as good as factory-made ones. This was done.
This plastic sheet played the role of the wall for a temporary carport or garage with opaque white walls made from greenhouse plastic sheeting. For some grommets, it and the punch easily punched through four layers of 6 mil film. I found this to be a quick and easy method. I only have one issue with this tool and that is that I cannot add grommets in the middle of the sheet, but that is not a defect! My only complaint is that my grommets were the wrong size, but they came with so many grommets that it's understandable.
It seems from reading other reviews I missed before buying this, I'm not the only one who has experienced this issue and the barrels appear to be misaligned and, therefore, do not close properly. You'd think you could just realign them since there are screws, wouldn't you? However, that would be wrong due to the barrel pieces being welded to each other.
Perhaps if I could just use an old school screwdriver to attach them I could get rid of the useless tool, but I have tons of grommets I can't use until I find another tool or do it the old fashioned way - I was angry and needed to release some anger with a hammer.
Related Products For KING PIECES Grommet Tool Kit Handheld Hole Punch Pliers Portable Grommet Hand Press Machine Manual Puncher w/ 500pcs Silver Grommets of 1/4 Inch (6mm)
