Titan 17005 2-Piece Stainless Steel Pry Bar Scraper Set, 7-1/4 x 9/16" and 9-1/4 x 9/16"

My friends and I are professional carpenters and cabinet makers, and I recommend these bars! Additionally, it is better than all other similarly shaped pry bars A variety of reasons contribute to the existence of bars In other words, they give you a lot of prying power but are thinner than other brands. As a result, you can get in as tight a spot as any pry bar (which is why you should purchase this kind of bar anyway so why does any other brand weigh so much? to take care of all your belongings It is important to pry with flat metal pieces so that you rock on the head from side to side, not back and forth in a manner that would bend the bar. These pry-bars are also flat pieces of metal. Generally, the bar does not bend very easily. I like these because they are two sizes, which allows you to use one for the messy jobs that get covered in crud (such as caulk and paint) and keep the other for the surgical jobs. And since it is 10 bucks for two at the moment, it makes sense to get two. Do you mean to tell me that? As such, they will never rust and will never leave marks on the work pieces or walls. *They do not rust, so they will never leave marks. Using them at the end of the day to clean grout and thinset from your tools and buckets is a great idea!.

Kason Taylor

| Jun 17, 2021

The reciprocating saw is one of my most underrated tools. It is the least talked about, costs less than many of the other tools, is smaller and/or less visible than many of the other tools, and is one of the less job specific tools I have. Despite this, it is the one that would probably be reached for most often, whether it is at home or on a job site. One of the many things this tool can do is so many things. I enjoy using it because it is very sturdy, has sharp edges (not knife sharp but I think it is sharper than my previous flat bar) and works hard almost as hard as I do.

Enrique Wagner

| Aug 31, 2020

I purchased a 12 x 5 x 6. This 5" pry bar replaced a carbon steel pry bar I'd had for many years made in the USA. Red devil might be responsible for this. Initially, I believed it was lost, but found it in the end. Only the 90 degree end of these stainless models is sharp, but other than that they look nice and are sturdy. Straight end blunt as a screwdriver, as is all the straight end. The fact that they did not finish the product would have seemed like a mistake had I not acquired two sizes. Both the sizes I bought are this way, so it seems that the design is intended in this way. My view is that it is now half as useful as it once was. Since I have used my old one to remove trim and scrape for a long time, the new ones will need to be sharpened before they can be used. This is a really nice looking tool, as long as that doesn't bother you. You might want to buy one that has already been programmed if you intend to use it You can choose from a wide variety of sharpened knives. I own a great many pry bars and wrecking bars that are both sharp.

Kinslee Flynn

| May 20, 2021

Working with high-quality trims and finishes has been my profession since I was a child Custom homes at the top of the market. One of these that I received a while back was a flat/pry bar I use on a daily basis. It was an unfortunate situation, but I lost the pry bar after a short while and had to buy another. There's a much more rigid set of painted blue pry bars that HD sells. These aren't the most rigid/sturdy pry bars I've ever owned, but they do the job almost 95% of the time. Their ends are not nearly as thin or as sharp as those. If you need to remove mouldings, the thin ends come in handy a lot. I can remove boards with less damage to mouldings and the things to which they are attached because the thin ends allow me to do so. Furthermore, since they are stainless steel, they do not leave any blue paint marks after use like those of the other brands. In summary, these are the pry bars I carry around and use every day because they work better in almost every situation than any alternate.

Harrison Yang

| Jul 30, 2021

For a 14" square room I needed to remove the trim around the baseboards. Throughout the process, I used all three From one end of the room to the other. One in front of the end baseboard was pushed into place, and then another one on top of it was pushed out to force the baseboard out. I was careful not to crack or break the baseboard because I planned to use it again soon. Plucking down these pry bars with a large rubber hammer was the easiest method. My plan was to position all three of these behind the baseboard once the end was decoupled from the wall. Once the end of the baseboard was pushed away from the wall, I started spreading out the three pieces behind it. Each wall of the room should be covered until the task is completed. In case you are interested, I bought that $4 blue pry bar set (it turns out they are plastic) but it came with an incredibly handy roll-up cloth holder that I put these 3 metal prybars in.

Laylani Barrett

| Jan 10, 2021

It's nice to have little pry bars like those, but I wanted something about the same size as my 5" Kinpex pliers and 4" Bahco adjustable wrenches. There will be a little tool kit that will fit in a pencil case. There is no problem with this. Even though it is so small and light, it is made of steel cut into 1/8" pieces. With the 90 degree bend, you get more leverage than your average bottle opener but the tool doesn't look out of place like a hose neck curve would on a tool of this size. In the middle part of the edge, there is a broken edge, but on the ends there is a sharp edge. You keep your hands clean with this nice touch. Not all of the edges of the nail puller are Using this method makes a nail less useful, but prevents a nail head from chipping a thin piece of Apparently I don't like the sticker, but that's the only thing I don't like. If you can use an adhesive that doesn't require me to get out the acetone in order to remove, that would be nice. All in all, this is an excellent pry bar for the little things in life. I highly recommend it.

Chana Rasmussen

| May 22, 2021

This is a super-useful product that's pretty hard to damage. The edges are sharp, mirror polished, precisely ground. Small, midsize, and large sizes can all be useful. The small one is very convenient, the midsize is useful, and the large one can be used for moldings and lighters, etc. If you need to pry but don't need a crowbar, use a duty pry. You may want to dull them or sharpen them even further, so you have the option. They're quite sharp, and depending on what you're doing, you may want to dull them even more. I like these scrapers a lot. An affordable price for an instrument that will last a lifetime.

Jabari Cunningham

| Aug 08, 2021