FFLP Airless Spray Gun Tip, 0.010"
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
You can use this tip as long as you use it on the Grand RAC-Delta With any airless gun and any airless machine, it can be used as a X tip holder.
I'm glad to see you! It is less critical which machine you use than the application and the product you are using. Personally, I would use a HVLP machine instead of an airless sprayer such as the X5. As for the tip itself, it is an excellent low tension tip with a fine finish. There are two numbers in the 210 angle and number. An angle of 20 degrees is about 4" wide at 12" from the subject. Look at the product specifications to determine what orifice size is recommended, and buy that size. Buy one with a greater angle so you have more control over In the past I have used them for shooting trim as well as
A RAC X guard is required to use this product. You can make do with this tip and a RAC X no matter what gun you have that uses the same guard as a Graco 695 Ultra, 395, etc.
Selected User Reviews For FFLP Airless Spray Gun Tip, 0.010"
The whole truth is out. In my first time using my airless sprayer for anything except siding, I used the gun to spray my house. Therefore, let's sum it up. . In the process of spraying some kitchen cabinets, I have been blown away by this tip. I have clearly In the meantime, I have sprayed the primer only, but will provide an update once the entire project is complete. In this case, we are using Benjamin Moore Advanced primer after sanding with 120 sandpaper and cleaning with TSP. No thinning was performed on the primer sprayed straight from the can. In the end, the doors had a flawless finish after being sprayed flat. Even though the primer was still wet, it looked almost like a polished surface. As for overspray, there isn't much to worry about and there's little to no fogging in the garage with this tip. This is real. has a much heavier density than what my HVLP gun creates, so it drops out of the air on contact. You should also wear a respirator! (I still wear a respirator. *)
I am using it with the appropriate blue RacX tip and a Graco ProX17 spray housing. The hose I used was 25 feet long, so I replaced it. The setup never occurred to me before, but for some reason I haven't already tried it. A few weeks ago, I bought an HVLP spray gun to use with my compressor, but it was terrible. There's just nothing easier to use about this setup. Probably less than one inch of paint from the gallon can was used in priming the sprayer. The paint was most of the time returned to the can during the cleanup process so it was not necessary for me to worry about wasting many cans of paint. As soon as the paint has been sprayed, I'll be sure to update.
Benny Moore latex was sprayed without thinning and let me say that the doors, cabinets, and trim came out As a result, the overspray was next to nothing and I was able to spray on the lowest setting (Graco X5 lowest setting = approximately 1000psi) which allowed me to move at a slower pace and control the spray more than I was accustomed I strongly suggest you buy one of these tips if you don't already own one! It was only when I used the that I felt a little hesitant. It was made with unthinned latex in size 10, but it worked extremely well!.
I don't know if I got a brand new product or a defective one, but it shoots in round patterns as if it has really worn out tips. To no avail, I experimented with the pressure to see if I could adjust it. I bought a tip from Sherwin-Williams that was identical The finish produced by Williams is really nice and it works well.
Graco X5 sprayers are what I used to paint kitchen cabinets with this tip. I was a very first-time user of a sprayer and did a ton of research first, so this FFLP tip came recommended by several As a primer It's a shellac-based coating It is painted The SW Emerald urethane enamel semi-gloss is available in eight colors It is glossy. Cabinet and door/drawer finishes came out as well as any professional or factory finished, which is very pleasing to the eye. However, the spray from this tip is great. Preparation is the key, of course. In this review, I included a photo of the paint finish since it can be difficult to get a good image of the finish.
I used this with my Graco TC Pro to paint interior doors and base trim, and it worked perfectly. It produces the largest fans I have ever seen for doors and trim, and I think this 210 produces the ideal fan width.
can be greatly reduced by using these tips & tricks I used far less paint than I normally would. The spray tips did not contribute to the creation of as much dust as regular spray tips. I love the finish that they produce! As part of my pre-treatment, I sprayed The trim and MDF are primed and ready to be painted Doors made from Masonite with a latex semi-gloss finish The paint is glossy, I didn't have to thin it, and I didn't have to distress it As if it were made of glass, it had a stunning finish! This is a great list of tips to follow!.
It is easy to shoot trim without having to use a lot of masking when using this tip.
It also works just as well on my cordless Graco TCPro as it does on my Magnum Pro X17, which is a superb latex gun for exterior and interior use.
Related Products For FFLP Airless Spray Gun Tip, 0.010"
