Schluter Kerdi-Shower Kit 38" x60", Offset PVC Flange
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Included in the kit are the following items A good way to start is to read KERDI-1. THE SHOWER - The Standard/Minus The center drain) *br>2 Kedi- Board of Directors A set of four low-profile shower curbs that measure 38" x 6" x 4". The waterproofing membrane of the KERDI product is 3' 3" by 33' and is 108 square feet. The product comes in a roll. The Band waterproofing strip measures 5" by 33'*1 The DRAIN PVC flange has one 2" outlet 4 on the inside and one on the outside In addition to those outside of The KERECK preformed waterproofing corners* 1 KERDI-PULL waterproofing tape Seal of approval The PS pipe seal measures 3/4" on one end and Seal of approval A seal for the MV mixing valve NOTE 1/2" is not the same as 3/4" The drain grate is sold separately (it is not
A section of the tray can be sliced through to accommodate, however, the tray has a gradual taper that will require you to fill in with mortise and tenon joints
In the past, I had one like this (32" by 60") in a curbless design. The height problem is something you'll need to sort out, either by lowering the shower area or by raising the outside of the shower, or by doing some of both, which is what I ended To keep the shower the most open (and to prevent stray water from flooding the shower space), you may as well add a shower curtain. The client uses a wheelchair, so a door would not be suitable for her. In addition to waterproofing the area outside of the shower, ensure that the area most adjacent to the shower is also waterproof. Ditra was used at the shower edge, and Kerdi was used to seal the seam. I wish they had come up with this size when we lived in the Old World. (Ditra is waterproof too, as long as there are no holes.) In this case, I had to extend the width with dry-pack conc, which wasn't difficult and it worked just fine. Kerdi must of course be applied to that area as well, sitting on top of the pan that has already been covered by Kerdi. The answer is not as hard as you might think. *br>I am baffled by why tile setters don't use this system or some variant As long as you test for leaks, after you form the base one time, either with the premade pan, mud, or both, you stick down the waterproofing, and you are ready for tile. The difference is one step versus two steps. In the old days, after you formed your base and let it harden, you would form another rubber layer on top of the first. Afterwards, wait for it to harden before you begin As well as the corners, they are covered in rubber. It makes no sense to me. A hard head and a closed mind. There is a two cent charge, but, yes, this is the perfect element for a curbless design.
You have to open two boxes, one is for the tray, which has dimensions 31x39x4 and the other
Selected User Reviews For Schluter Kerdi-Shower Kit 38" x60", Offset PVC Flange
Make sure you read more carefully than I did and you may save yourself some time and money by choosing another Sending two pieces measuring 38 inches makes no sense, but that is what you receive.
However, the learning curve is steep, so this is not an ideal system for everyone. The leak test I performed passed with flying colors after I followed the instructions carefully and watched the videos. It is important to be cautious when building up multiple layers in corners and the like, as small tiles, such as those that are commonly used on shower floors, will Taking it one step further, I applied a skim coat before setting the tile, which I was a little disappointed with, as I was hoping the presloped bed would allow me to omit this step. It was easier to save the cost of paying a plumber to install the pan and membrane in the project because I had always hired a plumber for those tasks. All in all, it was an unnecessary waste of time and money, although it may become easier as time goes on.
Please note that you will need to purchase the There are a variety of styles and finishes to choose from, so they aren't As far as I can tell, my only complaint is that the unit I received was labeled and packaged as an offset drain, but it turned out to be a center drain instead. A factory box had never been opened, and it was in its original state. Despite what we had, it was challenging to work with what we had.
The way I see it, I'm a doer I installed this system in my basement shower while doing a do-it-yourself project. I found it straight-forward and relatively easy to use. When it comes to my shower pan, I like to know that it will be waterproof and angled correctly. Make sure you watch some YouTube videos before you begin. My contractors told me being on this team is the best thing for them Here's the review I recommend everyone to use this system because it is the best.
I am very happy with it. It took me a zillion hours to watch videos and I think this is the best system for a watertight There is no easy way to achieve this! The midway point is always when I wonder why I am doing it. Whenever it's done, I'm glad I have a solid foundation, knowing that mold and water leaks are not going to be a problem.
The prices here are lower than at Lowe's or Home Cheap. I highly recommend this product as it's easy to make use of and easy to lay the tiles on. The business I deal with has never canceled my order or failed to deliver a product.
Overall, the information on the web was confusing, but more or less what you would expect. To complete the project, I had to purchase an additional curb to complete the two sides as the existing curbs did not cover the full width of the two sides.