PRIME-LINE Products M 6211 Shower Door Bottom Seal, 36-Inch, Clear
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
A product like this is designed for use with framed shower doors, and the product would be inserted into the bottom slot There are a variety of frameless shower door products available that may be of interest to you Depending on the thickness of your glass and the profile you want, it may take a while.
As the seal slides into a channel, there is usually a slot. Ensure that you get a seal that will fit in the slot of Wishing you the best of luck.
In the one I bought, the dimensions are 1" x 5/32" x 36"
I am very happy to hear from you! We do not have any T Sweeps configured in that manner. I wish you the best of We are pleased to have you as a TechnologyLK customer thank you for your business.
Selected User Reviews For PRIME-LINE Products M 6211 Shower Door Bottom Seal, 36-Inch, Clear
Upon looking at ratings for this product, I was amazed to see the poor scores. Yes, it comes in a roll and takes on an unpleasant solution is to let it rest in the sun for a few hours so it can relax back to its original The item is 36 inches long and will probably not be required to sweep the entire length of the shower door, so a portion of it can be cut off and thrown away. A third problem is that these sweeps are My trim always has to go over the bottom edge of the sweep. Use your judgment, but it only needs to be about 3/16 of an inch deeper than the top of the rising lip of the door footer to be effective. Anything deeper than that may cause the sweep to pull away from the track. You should, in other words, not be frightened to reduce the length and depth of this sweep to make it fit.
A few people mentioned how tightly the item was packaged, and one reviewer described it as You might want to check out this It should be taped down on both ends once it is opened to its full length. Make sure the blow dryer is set on the highest heat and that it is about five to seven inches away from the face Place it 6" from the edge of the sweep and move it slowly down its length. Less than two minutes later, it has flattened out without changing its shape. Put the product in the channel (make sure you clean it first because it's gross), cut it to fit, and insert the cap, and there you have After clearing out the gunk, it took me twice as long to heat and insert the sweep than it did to clean it out. Thanks for reading!.
As a result of my frustration with this product for the past month, I have replaced it with the Basco ECSCV284 Deluxe framed shower door sweep. It is snugly fitting.
The online retailer continues to win. bought a rubber seal at Lowe's several months ago and have been using it since. Rubber is too thick to flex well enough to seal the door easily, so the rubber does not flex well enough. In this case, I need to force the door open and shut. I finally found it and gave in to my frustration. It provides a great seal because it is made of a thin material, which easily bends over the bottom frame. Now my wife slams the shower door to save herself from having to deal with how difficult closing it used to be. Regardless of whether the glass shower door is standard or not, this seal will work. This track slides into the bottom track and has a height of about 3 feet.
Their specification for it was 5/32" thick, but I received one that was thicker. With the strip I received, I had to trim it with a razor blade with a lot of care. Initially it comes coiled up, but with a little time in a hot point of direct sunlight for a few minutes or in a 150 degree oven for 5 minutes, it is easily laid The flat surface will remain after it has cooled. It has been reported that some people have lost it. As a result, it is very important to measure your shower door slot before you order since they are not all the same.
I was fully satisfied with the fit of this item. The guide was thoroughly cleaned of dirt and grime accumulated from years of The replacement fit like a glove once it was cleaned. Please read the following note before using this application. As long as you go slow and carefully, you will not have any problems. You can then trim off the excess after you have attached your aluminum shower guide. As a side note, I checked several hardware and plumbing stores and they did not carry this replacement part. Even a long-established plumbing supply store that usually carries parts and advice did not carry this.
In the house I just bought, the stand-up shower came without the door sweep, so this should be exactly what I need. I'm unsure if there is a learning curve here or if I am simply too lazy to learn them I'm not physically challenged (Mario, I am not), but these guys have such a tiny head, it is hard to make them work properly. I shoved the 3/4 inches together so it was thick enough to stay in the frame, but I had some 3/4 inches that were too short but had a much wider head so I could use them. Also, I understand that they always come in the form of a giant roll but that's not a very efficient means of transporting them, so it always has little bumps, and I feel like it still leaks water, which defeats the very The fact is that they are all being sold this way, not just this one. Be sure to consider if the smallest head in the world will serve your purposes and remain within the confines of the.
Despite the good quality, the door on my shower is too long. As the strip is easily cut to fit the width of the shower door, cutting it to the required width isn't an issue. Additionally, the T portion of the strip fitted perfectly into the groove at the bottom of the shower The length of the strip hanging from the bottom of the door when it's installed, however, is almost twice as long as I am able to get into my door and still close it properly. The piece is a bit larger than I anticipated, and I've tried cutting it down to size, but getting a good cut with the same length all the way across seems impossible. There was some sloppiness to the cut so it isn't as pretty as it could be.