Zengest Full Extension Less Noise Ball Bearing Drawer Slides, 10 Inches, 1-Pair
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
A small lever will be visible when the drawer slide has been pushed out all the way. You have to push that to the side for the inner glide to be released from the outer part. I'm not entirely clear on this. Although no instructions are given, I agree It works the same way for all slides of this kind. It's hard for someone doing it for the very
The length of them is approximately 1/2". There will be a little more length from the slide in total than there would be if it wasn't for the metal. During my use of this on my bureau, I did not encounter any issues, and it fitted perfectly. Slides of this quality are actually better than the originals I had. The slide moves smoothly and they are quiet when moving. Since they contain a significant amount of lubricant, you might want to wear nitrile gloves when handling them to keep your hands clean. It is not uncommon for drawer slides to be standard-sized, and the screws that go with them are also standard size, so there is no problem.
The cutting board shelf is indeed what I used the trays for
The length in the collapsed state is 10 inches, while it is 20 inches when fully extended.
Selected User Reviews For Zengest Full Extension Less Noise Ball Bearing Drawer Slides, 10 Inches, 1-Pair
made a slide-out shelf for a cabinet out of a pair of the 10" slides. As opposed to using them on the sides, I decided to install them under the cabinet instead. They worked just fine. All you have to do is ensure that the two slides are parallel and square to I like how they operate quietly and look nice, as well as how sturdy they are. If you want to separate the parts, just watch out for any grease or whatever is on the inner parts. An instruction sheet would be helpful showing how to separate the parts so that they can be installed. You don't have to be an expert to figure it out, it's just a matter of principle.
It was perfect, but I do wish it came with an instruction guide. I managed to figure it out on my own, though. Fit well, are built solidly, are strong, extend to the full extent as described, and are definitely a smooth and quiet ride. used them to replace old, worn out, rusty ones that only partially extended and found them to work even better than I It would be my recommendation to other people who are looking for a similar product!.
Despite the fact that these worked well for one of my projects, I ran into some problems with another project and turned these slides into a bent As soon as I removed them and replaced them with Accuride slides for marginally more money, I was amazed by the quality difference. It would be impossible for me to bend them out of shape despite my best efforts. According to my measurements of the thickness of the metal in the slide bodies, they are about 40% thinner than the Accuride slides. A large improvement has been made in the engineering of the more expensive slides as well. An elaborate project takes a lot of time to complete, and it is a shame to put cheap hardware on it. The better slides will be presented in the future. After learning my lesson, I'll never do it again.
Inside an IKEA wall unit, I installed a Bang & Olufsen Turntable. My friends enlisted me to drive to the nearest IKEA, where I found a board for two dollars that perfectly met my needs. In addition to the original IKEA base cabinet, I also mounted this ball bearing slider kit on a scrap piece of wood that I got from Ikea. My investment totaled about $14, so I had exactly the right thing to mount the turntable to the cabinet with a pull-out tray.
Two of the two sets I ordered were defective one of them had ball bearings that fell out, so I was forced to return it. It was determined that the replacement was incorrectly manufactured, but it was sent the next day. Despite the bearing slide being on the wrong side of the metal nip stops, it still worked. I pried the nips up with a small screw driver once I had hammered the nips down with a hammer and punch, moved the slides in their proper spots, then hammered them down again. Once that was done, everything worked perfectly. It is hard to find 10" slides, though this is either a hit or miss product.
In addition, it has a rubber stop so you don't have to worry about sliding when you push it all the way in, and it also has It allows you to pull out a slide by holding it in place. In the past, I have used ball slides for my drawers, but they would slide out when I did not I have provided a solution to that problem in the following slide. Soft close slide mechanisms on other slides have not been as durable as the ones I've used.
I enjoyed using the measuring guide and the instructions. I tried all of the local hardware stores (Lowe's, Home Depot, etc. ) and couldn't find it. It took me a while to figure out how this would work, but thankfully there was a helpful guide to help me figure out what size to buy based on the measurements of my I was impressed with how easy it was to install and how well it worked. I am very pleased with this purchase and would recommend it to others and use it.
Rather than buying them, I built a set of night stands myself. To make my own drawer slides, I made dovetail joints and modified them to make them slightly longer. In the end, I decided to go with a metal, ball-bearing guitar cable Those with bearings are known as bearing To make my drawers slide properly, I needed the right size slides (10"). There are all the big-wigs out there- There weren't any that size available in the big box retail stores close to me. They sold only 15" and up, and they were expensive. Choosing these after finding them on Amazon was a great choice. I enjoyed them a lot! As it turns out, I mounted them on the bottom of my drawers (not the sides) and they worked great. I really liked them and they suit my needs perfectly. door slides smoothly and quietly open and close. I can't find a single negative thing to say about it. These are perfect if you need an odd size drawer slide, such as a 10" slide.