WiFi Electric Remote Control Drapery System,Curtain Motor with DIY Tracks,Alexa Google Home Control via Tuya App Timer,Slide Shade Motor compatiable with Broadlink(2.2M(85 inch))
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Hey, you're right. It could be one. The 9M as it was had a DIY 1 meter track that had a 0 meter width. With a dimension of 5m and a number of The tracks are two meters long, so it can sustain one person. I would like to thank you 9 times
We would be glad to give you more runners for this WiFi Electric Remote Control Drapery System Curtain Tracks if you tell us how many you need through Amazon's message system
This motor can handle 10 meters but need to use two motors, one for each corner of the warehouse since we only had eight meters of track in the FBA warehouse. It can be used with 2 motors and lanes up to 10 meters long. If you need support, message the seller
Selected User Reviews For WiFi Electric Remote Control Drapery System,Curtain Motor with DIY Tracks,Alexa Google Home Control via Tuya App Timer,Slide Shade Motor compatiable with Broadlink(2.2M(85 inch))
My curtains were put up by myself but you might find it useful to have someone else assist.
It is difficult to understand the written directions, and the videos appear to be better but still are lacking in I have included my notes below. br>Installation by a single side draw Two meters) The first paragraph. All Allen screws on both sides of the track should be tightened. You should pay attention to the alignment of these. Make sure all rough areas are sanded. Plating the track slotted side down on a flat surface is your best option. * * 2. The side with the motor slot should face up on the pulley. Straight piece) from the end pulleys to the motor Then set aside.
3. Use a phillips head screwdriver to remove the screws. You then need to push the belt around one of the pulley ends after it passes through the channel on the bottom of the assembled track. Once the two-piece plastic end cap comes out, seal it with the plastic two-piece end cap before inserting it into one of the plastic trolley pieces with the wheels pointed Pull the belt halfway down the track with the attached trolley in place on the top The fourth point. Repetition of step 3 should be done on the opposite side. Once the belt has been fed through the pulley, attach the trolley and end cap. The trolley should be inserted so the wheels face the pulley you just fed the belt through, and not the center of the track. You can now place the pulley ends on the tracks. Pulleys on each side of the track can overlap by about 3 four inches, but there is some adjustment available. The trolleys should meet once you have pushed them together. The fifth point. To determine how long the belt should be, you need to measure it. There needs to be a meeting point between the two trolleys, where they will be connected through the middle. You may need to trim 1" or half an inch from the belt to ensure that the ends meet correctly and the belt can be properly cinched. In this case, you will have to undo or cut off one of the trolley ends and repeat All of these pieces are available in extras. This is 6. Incorporate the comb-shaped piece into the belt after adjusting the trolleys so that they are at the same height Vertically into the middle of the two trolleys is a metal plate-like piece. Be certain to carefully consider the direction in which the curtain should be facing. An S-bolt is affixed to the leading edge Place the shaped metal piece through the trolleys and add the three hole backer plate on the opposite side. A threaded hole is included on the backer plate, so no nuts are needed. The curtain rings should be inserted the correct way on the The tensioners need to be inserted. The seventh point. The system needs to be tightened now. When there are two of you, it is more effective. Make sure that the overlap between the pulley and the track is equal. One tensioner needs to be fastened. You can test the operation by pulling the trolley with a partner who is varying the tension at the unfastened end of the pulley. At the point where the trolley can move most freely, tighten the remainder of the tensioner. The eighth point. The hardware is provided for mounting on the wall or ceiling. Considering the weight of the motor hanging from the track, it makes a lot of sense. Item 9. Glue motor and power supply to the back of the machine.
After a few days, I noticed that the motor did not work and contacted the seller. At first, they assured me they would take care of the issue, and then they completely disappeared and stopped responding to me.
Very good - works as recommended, and you can use Alexa to control it. My motor runs very quietly, but I have been airing it for more than 3 months now with no issue. As for the down side, the installation instructions are worthless. I am basically using my imagination most of the time to install the curtain, as I am not able to control how wide it.
The product seems sturdy and of good quality. I would like to see better instructions, especially for hardware and software that is optional or additional. (setting up the smart hub and connecting to it) My overall impression of the result is very positive.
The instructions were not that easy to follow, but once put together and up, it worked.
I like it.