Pelican Protector 1700 Series Rifle Cases
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Yes, you can secure the case with a lock. There are four holes in which locks can be inserted. No, I do not recommend it. Master Lock locks with the code 7KALF. These locks are a perfect fit for the case and are far more durable than the light weight TSA locks. You can also purchase them from a locksmith, who will have them keyed alike for you. I only need one key to open four cases with eight locks. Try the following steps for travel: 1)Arrival early; the TSA screening process can take up to 45 minutes. 2) Carry current firearms travel documentation from the TSA's website and the airline's website. This is a massive accomplishment. This way, there will be no ambiguity about what is legal and what is not (TSA/airline representatives are not standardized as they should be). If questions arise, which they will, request a supervisor and show them your current documentation, and they will quickly back down. 3) After completing your declared card, take your case to the TSA inspection area and/or accompany it there to watch it be scanned. If a lock needs to be opened, you'll be standing there with the key at this point. Do not open the case again once it has passed this point.
HEADS- UP guys.. br>You don't want 'pick-up' at all. For a gun case, pluck' foam. 'pick- pluck' foam is used for items that are small, delicate, and light in weight. instrumentation, for example. 'select-'br>'select-'br>'select 'Pluck' foam is made up of the following ingredients: Soft, easily damaged when used repeatedly (the larger/heavier the item [rifle], the tighter the fit [which you want]); Because it is made of Polyurethane, the "open cell" foam will absorb oils, moisture, and other contaminants more quickly. br>True gun case foam consists of the following: Because it's made of Polyethylene, the foam is stiff and tough, and it won't absorb anything because it's "closed cell." It will take time and precision to cut it to the exact fit you desire. With a heated wire rig, if possible. It'll all be worth it in the end. br>* Be aware that if you make a mistake, you will be required to replace the sheet (2" thick; In most cases, the one you cut will cost $50. The good news is that you can use replacement sheets to create various rifle carrying configurations for the same expensive transport case.
Foam was included in my case. They almost always do, in my experience.
I just double-checked my measurements, and it's 42-inches long. My rifle has a 1/8" barrel and a 41-inch barrel. I'm only 3/4" tall, so there's plenty of room for me. Like you, I was concerned, but I took a chance and it worked perfectly on size; now this is UN-UN-UN- UN-UN-UN-UN-UN-UN-UN-UN-UN-UN- Cut foam gives you two pieces for the bottom, the 2" thick one is the one you cut - I haven't had time to draw and cut it yet - Too Lazy! I simply removed it until I have time to replace it; however, I may want to add a second rifle and possibly a pistol or two. What I now use is low-cost Styrofoam packaging, which can be found in garbage cans: ) in order to keep it in place. The reason for this conversation is that I discovered that if I angle the rifle in the case, I have a lot more length available. I'm confident that this case will meet your needs perfectly; worst case scenario, you'll have to hold your rifle at an angle, which I don't think will be a problem. It's a lot better than carrying a bulky case. br>I recommend that you start with the Styrofoam until you feel comfortable with it; you may want to cut out for other items as well (such as bipods, clips, a field cleaning kit, and so on) - all of your chopping should be done at the same time: I simply use 8"x8" 2"x2" pieces. 5 or 6 spots with a total of 10" I hope this information is useful! Maybe a lot more than you requested, but I'm excited about my case and want to help: ) I think the foam on the ends is unnecessary; my stock has a pad, and the barrel end? I'm not going to drive tent stakes with my case. Because there is only one handle on the end of this case, the barrel must be placed here.
Selected User Reviews For Pelican Protector 1700 Series Rifle Cases
Pelican's gear has always appealed to me. They always get the job done and make sure that whatever is inside gets to where it needs to go safely, whether it's for my photography gear or an arsenal of guns. This was purchased to store and transport my LWRC AR-100. 15 and Sig P220 are two of the most popular handguns in the world. It easily accommodates both, with plenty of room for extras. The hinges are built to last and are made of high-quality materials. The exterior is beautifully designed, with a folding handle (a nice touch that not every case like this has) and smooth, positive latches. The interior of the bag fits any AR, even those with a lot of accessories, and there's still room for magazines and other items. The wheels are also a nice feature, especially when traveling with multiple bags. Because Pelican cases aren't particularly light, the shorter model saves a few pounds over the longer model. The fact that this case can't hold longer guns is a trade-off, but the fact that it's a few pounds lighter and shorter can be a big help if you travel frequently. Cutting the foam - br>br> This is my first pelican case, and cutting the foam was relatively simple. You can watch YouTube videos to learn how to remove the middle layer before cutting it out. Lay out your items in the opposite direction of how you want them to go so you can cut the foam and flip it over to get the correct layout. Make sure the weight is distributed evenly so the case isn't too heavy to carry. The solid foam inserts are simple to cut and shape, even when thinned out when cut close to the edge. I recommend drawing an outline of whatever you'll be carrying in the case with a Sharpie and then cutting a quarter-inch inside the outline to ensure a tight fit around your belongings and eliminate any movement in the case. Cutting the foam was done with an electric fillet knife. I cut the foam on my bar top by pulling it over the edge of the table as I cut, allowing the knife to freely pierce and cut. The best cuts came from holding the knife at a 90-degree angle up and down. I'm picky about these things, and the end result exceeded my expectations. I sprayed several coats of Plastic Coat spray on the foam after the final cut to give it a firm feel. It also has a better hold on its shape. My rifle with the scope mounted, pistol and all the accessories fit fine in this case and I 100% am 100% happy.
Okay, I'm sure everyone who reads this is familiar with Pelican. As a result, I'm going to avoid the obvious. Pick-and-pluck foam is not included in this case. This is block foam in its most basic form. At the bottom, there are two sheets. In addition, there is one sheet of paper in the lid. I cut out the slots with a razor-sharp pocket knife, which was a little messy, but the cuts aren't visible once the slot is full. I keep mine in the bed of my truck during the day (rain or shine) and take it in at night or at work because I can't afford for them to rust or get lost. I use ABUS padlocks and a big chain to keep it in the bed of my truck during the day (rain or shine) and I take it in at night or at work. Rain and humidity are no problem for the water seal. I've left my case on concrete for hours on end and haven't had any issues with water, and I'm impressed with the ergonomic feel, wheels, and air lock vent. I'm not afraid to throw it around because it weighs about 60 pounds when fully loaded. Mostly because of the Pelican guarantee of "you break it, we replace it. ".
I returned to the original location. Between this Pelican 1750 and the SKB Double Rifle case, I switch back and forth. I believe either option would have sufficed (both SKB products are excellent). However, I ultimately decided that I wanted to tailor my rifle to the case. I alternated between the years 1750 and 1720 as well. As a one-size-fits-all solution, I ultimately chose the larger 1750. I don't travel with multiple guns very often, so instead of buying multiple custom cases, I bought extra foam and cut out forms for several of my rifles. I cut the foam with an electric knife and had mediocre results; perhaps on the next rifle, I'll do better. I should have paid more attention to keeping the electric knife true and perpendicular to the outline I drew. Others recommended laying out the rifle in reverse to how you want it to end up resting, so that when you're done cutting the foam, you can flip it over and hide your tracing marks while putting the majority of the weight over the wheels. What matters is that the rifle is snug and secure, regardless of my cutting job's aesthetics. I struggled to spend the money on this case, but in the end, it's a small price to pay compared to what most of us have spent on our rifles and the glass that comes with them. I highly recommend this Pelican case if you travel with your rifle or simply need a case to protect and secure your investment.
I hate to say it, but this case does not impress me as much as I had hoped. I have a few more Pelican cases, as well as a lot of the high-end Pelican cases. The same high-quality features found in models like the 1200 simply didn't translate to the larger 1720. The latches, for example, have a shorter travel distance and lack the signature confidence-inspiring "kchunk" you're used to hearing. The latches have been described as'soft' in some reviews, which I completely agree with. The case itself isn't quite as sturdy as I had hoped, and the panels have a lot more flex than I anticipated. Although I have not tested the waterproofing, there appear to be some visible panel gaps along the seal. br>br>I'm not sure, but I think I'll keep it. It accomplishes the goal. I just assumed it would have a higher quality feel to it.
The Pelican case, as usual, did not disappoint; it is well-made and nearly indestructible. It costs more than the Plano brand, but as with scopes, "buy once, cry once," and how many times do you need to buy a case like this? Replace the foam in the case with a twin-size memory foam mattress topper (approximately $40 on Amazon). You won't have to cut it, which means you can use this case for multiple guns without having to buy separate foam for each one.
Related Products For Pelican Protector 1700 Series Rifle Cases
