ArmaLaser Designed to fit SCCY CPX 1 CPX 2 CPX 3 DVG TR10 Super-Bright Red Laser Sight with Grip Activation

Bought this for her, and the first one failed to turn on. I contacted customer service, and a very pleasant woman (Kim) sent me a replacement, which my daughter received the following week. My daughter and I went to the range, where the laser's battery died after one and a half hours. Later I changed the battery and she was able to shoot again. After it came back on, it worked again. My battery problem has been solved. I called the customer care number again and talked to Kim. She apologized for my problem and she's sending me some batteries. She is also having a technician take one of the lasers and put it through its paces to see if it has the same problem I did. Kim, thanks for your kind words!.

Carolyn Vazquez

| Jan 23, 2021

My wife has been asking me where she can get this. There is a lot of difficulty finding the front sight as she is losing her Her laser treatment helps her a great deal. As soon as you grab the pistol in a ready grip, the sight will turn on automatically. It can be turned off to store the weapon. Her SCCY CPX2 fits perfectly with this product, which is much cheaper than the others. Purchasing this product was a good decision.

Ricardo Warren

| Dec 12, 2020

The tech at SCCY Industries suggested this to me, so I purchased it. His CPX is now equipped with one In addition, the beam was highly visible over a distance of several hundred yards. In addition, its price on Amazon was the lowest I've seen anywhere. It took me about 15 minutes to install the software. Reading over the instructions several times took a lot of time for me. Due to the fact that this is my personal security weapon, I wanted to ensure that everything was done correctly. (I could have taken it to SCCY and allowed them to install it as well. )

Fitting and finishing As for the plastic housing or quality of workmanship, I have no complaints. The sight clamps solidly over the trigger guard. When it comes to clipping it on to the trigger guard its a little difficult, but I believe it's necessary in order to keep the sight firmly in place. Having a CPX is a big plus There is a slight difference in the shape of the underside of the frame versus that of the CPX In ArmaLaser, two small spacers fill in the gap between the laser and the lens. It is a bit of a hassle to fit them properly, but they work well. As I sighted the laser with my gun's iron sights, I was able to sight the range. As a factory adjustment, the laser is positioned approximately an inch below the iron sights at 25 feet, which is the recommended distance. As of now, I am planning to leave it there. There are two "on" switches on the phone, and that is the one complaint I have heard. For the laser to work, both switches need to be on. An on/off switch appears on the side and a contact plate under the guard. The laser needs both switches to be "on. ". While gripping your weapon, the side of your middle finger rests up against the contact plate, completing the circuit that your finger makes across the While holding the gun, I do not have any trouble activating the laser. In the event that your hands are extra dry or if you're wearing a glove or if you're infected with another disease * Since your finger is not able to complete the circuit with the plate, your finger cannot operate. In the kit, you will find all the necessary tools and parts to install and set up The situation at this point is quite satisfactory for me. I enjoyed the laser sight, but one thing it did show me was when I squeezed the trigger, my aiming seemed to jump to the right slightly (inch or so) Hopefully I will be able to do that soon!.

Angel Wade

| May 11, 2021

The laser sights this manufacturer offers seem to be decent, but I do not have a lot of experience with them. This beam is powerful enough to be easily visible from any distance a handgun would be used from. When gripped by my SCCY CPX-D, it turns on reliably It is still early for me to comment on battery life as I haven't had it long and has only been used for a hundred rounds or so To get it accurate, I will have to take some time. As a first attempt, my adjustment was decent at 20 feet. If I was just looking at my hips (not literally), I would shoot from there I get all my shots on the paper silhouette, so it may not be "dead on balls accurate," but I don't have a Craftsman model 1019 Laboratory edition, signature series torque wrench, so if you break into my house I'm still going to kill you. A little update. )



**. It appears that the laser pattern is dirty or cloudy years later as if the lense has become With the exception of using microfiber swabs, I have been unsuccessful in cleaning with them. It seems to me that the residue on the lens may be permanently etched. It will be interesting to see where ArmaLaser goes from here.

Poppy Johnston

| Jun 29, 2021

Good package, nice user guide, fast and easy installation, super bright even in daylight, reduces the amount of room with inside the trigger guard, although not a problem for me. Overall very satisfied, highly recommend, a must have.

Knox Davies

| Nov 11, 2020

Three out of three completed.

Annabella Woodard

| Aug 09, 2021

The trigger guard of my new SCCY CPX 2 pistol is the perfect place for the AR style trigger. * Installation was straightforward and feels "Switch" for turning the laser on and off is not a moving switch, but a touch pad on the gold colored pad that is activated by the touch of the second finger. *seriously, i turned on the laser light very fast and took no time at all. I would recommend it.

Lexie HOWELLS

| Aug 18, 2021

A great feature of this design is that it can be left on and that the laser only comes on when the gun is grabbed. By placing your index finger on the trigger guard, you move the contacts together. It is easy to put on and take off the laser. It was because I thought this was the best laser for the SCCY pistol that I purchased.

Cairo Moore

| Feb 03, 2021