Hogue 18400 HandAll Sleeve Grip, BGS, Sheild LC9, Black
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
The answer is yes. On my LC9s I have a striker instead of a hammer, so it is an LC9 with a striker. Make sure you read the installation instructions thoroughly. For it to stretch on the gun, it may have to be heated.
If you have a P 11, I would suggest you try seeing if there's a Hogue grip made especially for that? LC9 grips are thicker than those for the P 11 so I don't believe one made for the LC9 would fit the P 11. In my possession, I am both an Ec9 as well as a P 11. As a result of the tight fit with the Ruger, I wouldn't try to install it on the Kel-Tec This is technology.
Do you apply pressure to the grip with your holster? The grip fits snugly over the handgun because it has been molded specifically for it. front of the grip curves up to the magazine release and the beaver tail of the grip follows. In this grip, there is a slight swell in the palm. With an Alien Gear 2, I keep track of my fitness. It fits really well with my Kydex IWB 0 (Kydex). It might be of use to you. You will not be let down if you purchase one of these and it fits your firearm holster.
Selected User Reviews For Hogue 18400 HandAll Sleeve Grip, BGS, Sheild LC9, Black
This is the right size for my M&M You've got P Shield just right! Just enough size to give my large-sized legs the girth they need The handle feels really comfortable now that my hands are accustomed to it. open the box, you think there's no way that grip is going to Be sure to read the instructions from beginning to end, and to thoroughly warm the rubber as directed. Having patience is key. There will be no problem with it! It took me about 15 minutes to work on it to a.
I am amazed at how tough it is Indeed, I am getting older, but I still have fun. It really is pretty much their directions that must be followed. In any case, I used WD-70 as a lubricant It is better to use 40 instead of 40 This is based on They recommended a) one. As opposed to using it to get a grip on, I needed it so I could remove the plastic sliders once finished. I find the Ruger EC9s to be a great match for this product. It's a very smooth, but sharp edge meets the fleshy part of the thumb just below the slide no particular threat, but blister city in less than 50 rounds. I'm hopeful that this grip, with its beavertail, will prevent skin from getting worn off. The grip on a previous model was much easier to install, but it didn't extend to such great heights.
It fits the Ruger lc9 very nicely despite the fact that the word Ruger didn't seem to be present in the product description. Previously, the stock grip pinched my fingers and left them raw, but this grip adds some needed thickness and comfort while maintaining a Since my hand ached when I picked up the LC9, I was regretting picking it up, but thanks to this grip, I have come to love it.
The installation process is very simple. My solution was to use either glass cleaner as lubricant or to immerse the grip in boiling water for a few minutes to make it more flexible. I managed to put it on in a few My hands feel very comfortable when I use it, and it looks fantastic Will test it out on the range as soon as possible. I am pleased with the service so far.
My water was boiled, and I poured it into a measuring cup with the grip, and I let it steep for around ten minutes. Using the two pieces of packaging I cut off according to the instructions, I placed them into the shoe using a shoe spoon. After I cleaned it with window cleaner, I added the plastic slide and I think it helped a lot. was able to do mine in just one attempt, and plus heating time, it took a total of 15 minutes. I have already noticed a great improvement once the palm swell has been installed, as it fills my hand much more efficiently and makes gripping my shield less likely to twist. Hogue grips have been installed on three different pistols in the past and none have disappointed me. As for me, I had my shield for about a year before deciding to get these, so if you're considering them, go ahead and buy them.
One for my 9mm Shield and one for my 45 Shield. Although the model is a bit short for the 45 shield, it's because I was supposed to get one made for the 45 shield, which I have now ordered (18300). As far as possible, I seat the rear beavertail high, and I have the Hogue seated as high as it possibly can Up to where it would inhibit the use of the mag release, and anything further would shut it down. I know it would be nice if it were intentionally a bit long, so that it could be trimmed away to allow for customized I will replace it with the 18300 once I receive it when it arrives, but it still works well even with the 45. In other words, the lack of full coverage is merely an aesthetic consideration, which has no effect on the wearer's functionality. If you have large hands or long fingers, this program is for you The hands and fingers of a male should be medium to large in size The tigger reach is otherwise too narrow and this grip provides a major improvement – particularly to the painful- otherwise too short grip This is the second shot. There were no money and no money Undercover subcompacts typically have the P Shield (common issue). The point of view was enhanced by it To improve the aim-and-shoot capability of the gun by significantly improving the trigger reach, which for me had been too short for what I considered confident use of the pistol. A shield made of polycarbonate. PS, of course), but I was concerned that the short trigger reach of the Shield with my hand and finger size would lead to muscle strain. When I should need to quickly draw and shoot the firearm, I may suffer memory problems, as well as a loss of accuracy. It is evident that the extra beavertail material, the minor addition of thickness throughout the Hogue grip, and the slight flaring along the grip sides improved the comfort and shooting performance significantly. Guns are able to carry a lot of ammunition. When I used to shoot it all the time at the range, I suffered from pain. (For your information No negative impact is caused by grip b) The tiny, hard, abrasive, thin normal grip was uncomfortable for my moderately large hands, and the short trigger reach was a nuisance. A recent study suggests there is no longer any problem, or at least there is far less of one. These grips are excellent and I am extremely pleased with them. Both of them were installed in 10 minutes or less. The Equalizer tool, which can be ordered on Amazon, is a great auto glass cleaning tool I used and strongly recommend. Plastic is the material used in this hard little wonder. This is a versatile tool that you can use for many purposes. A perfect example of that was this. Due to the material of the grip, there is no risk of damaging the gun. It will probably work just as well if you do something similar. Applying a very light layer of olive oil to the inside of the grip, carefully prying, sliding, adjusting with the Equalizer, and a little patience--will help the grip feel much better. The easy way- A little something to keep you in the mood I had no difficulty applying the grip precisely.
It's amazing how much better my grip is with this sleeve. When I first got my LC9s, the grip or the pistol was quite rough, and I would leave the range with raw fingers. Having the sleeve on my gun has not only made the edges less sharp/rough, but also made it easier to grip and improve Now that I have my gun, I am so happy. I found the installation process to be straightforward. In less than a minute, my husband had it turned on after warming it in hot water.
No cursing involved, which is always nice.
I've been to the range several times since installation, and I've found that the sleeve performs well. In addition, the grip makes it easier to control the LC9s since it is quite peppy.
Related Products For Hogue 18400 HandAll Sleeve Grip, BGS, Sheild LC9, Black
