TFD The Tray | Compatible with Peloton Bikes (Original Models), Made in USA | Spintray Desk Tray - Premium Acrylic Holder for Laptop, Tablet, Phone, Books & More - The Ultimate Peloton Accessories
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
As a result of your question and the seller's response, I did a quick check into the matter. As a reference, using Tap Plastics, we can estimate the cost of the base material at $35 assuming no waste is produced on either end. In addition, you must account for shipping fees or gas, in addition to time. Lastly, manufacturing takes place. It would most likely be laser cut, although you are going to need a special lens on many lower cost lasers for such an application The focal length to make a decent cut should be about 1". In terms of the pocket to hold the inserts, you could do that with careful calculations in your laser setup, or you could use a CNC machine. I'm not sure about insert manufacturing - that might be easier on a CNC machine. The price wouldn't be too high if it was a laser job or purchased independently, but in reality, it's probably not as high as a few dollars at most. Adding the time to manufacture, assemble the packaging, label, and ship the order, and the cost of damaged or lost shipments, reveals the total cost of the shipment. Last but not least, you can add a ) costs and margins. While he may be offering acrylic at a discount price, I doubt the product is going to make him much money.
It is easier to use because of the slope and my computer does not slip. Although the textbooks I am reading slide (since they weigh less and have no grip), I am still reading them. Rather than using a clip at the bottom to keep the page from sliding, I instead use a paperclip.
it's no trouble at all. It will just come off with a little effort. As long as it remains in place due to gravity There are no clips or anything needed to adjust it. I regularly wear it and take it off.
Selected User Reviews For TFD The Tray | Compatible with Peloton Bikes (Original Models), Made in USA | Spintray Desk Tray - Premium Acrylic Holder for Laptop, Tablet, Phone, Books & More - The Ultimate Peloton Accessories
In the middle of the part that goes over the handlebars, there are not rounded edges, but pretty sharp ones. Despite the round edges on the rounded ends of the other parts of the table, this sharp part of the table cuts into the handlebars and makes deep holes on mine. Were a few additional seconds taken to also round over the inside edge of the box during fabrication, there would have been no It was still sad that I had to be the one to do the roundover, but it was doing it myself prevented any further damage. There is no need to be a genius to make that simple adjustment. The creator of this product should make that It's a really nice table and the size is perfect for people of petite stature. It's a bit awkward to use off the bike! I don't like the angle it sits at (your mouse will easily slide off the desk if you have it there. As a result of the adhesive pad (that I put on mine, I can use my optical mouse (which, since the product is clear, is mandatory since the mouse won't work otherwise), I am updating Fits the new bike plus (bike+) model, but does not fit on the old model.
There is work, grad school and health (both mental and physical, something the peloton helps me with) and to top it all off, I'm stuck playing this game. Changing the game! As a reader or typer, I can log miles on my computer. Having to move more and read more makes me more focused on the reading and has allowed me to ride farther. The winner is The winner is! In the past, I've not had any problems with computer or book To change it up, I usually do the "just ride" for a while. After that, I do an intense climb for 10 minutes (and see my favorite instructors) and ride some more until I am completely exhausted.
My favorite part of the product is how quickly it came. There are so many messages in them that Russ writes. It was great but the edges were very sharp right at where you attach it to Peloton and you keep your hands there a lot of the time so I got cut the first time I used it. Although it did not have sharp edges around the whole board, that specific section of it right next to the peloton did have sharp edges. Despite this picture, it has been a week and the cut has almost healed, but I still bled quite a bit and it was much worse than shown. I also barely managed to keep my legs off the board, even though I tried to adjust it. My height is 5'8 and I'm not quite as short as you are, but just letting you know. Despite my dislike for the seeker product, I appreciate what it does , however there are some issues that need to be addressed and the price for what it is is quite high.
Using a DIY treadmill desk, I was able to maintain an active lifestyle while working. We got our Peloton bike in 2016 and I have been experimenting with how we can use it as an active workstation as well. I was told about the Spin Tray by someone. You can use a laptop and be exercise-active with the Peloton and Spin Tray installed on the handlebars.
The spin tray is secure on the bike and is a little sticky (without being gross) so your laptop won't It would be my pleasure to suggest any changes to The Spin Tray is another lazy Susan for inside cabinets that is similar to the Spin Tray. Normally, if someone searches for Spin Tray, they find that first. Would Pelo Desk and Pelo Tray be found next? I'm telling all my Pelo friends about it, by the way. This is a great product.
I liked the great surface area and felt it was a very sturdy product. I can easily hold my laptop on the tray, and it's great for holding snacks and drinks. Having to dump some of my soda into a smaller bottle (usually an empty Gatorade bottle) was my biggest complaint about the Peloton. I couldn't fit my 44 ounce soda cups on the bike, so I had to dump some into smaller cups instead. provides me with plenty of surface area to hold my Diet Dr Pepper, and I can even drink it while I'm taking a scenic ride with Leanne or a Disco Ride with her! While you can still drink while sitting, it is harder when you have to get out of the saddle. With the straw, one would not want to scratch the roof of their mouth! When I drink and savour the sweet nectar of the carbonated syrup, I just slow the cadence to a screeching halt. The only thing that makes it inconvenient is that it won't fit a large It needs to go on the back of my weight bench The only problem is that it is next to my bike's food station. I realize that is a personal preference and not a defect.
In all seriousness, this tray is sturdy and well-constructed. Build is top-notch. I highly recommend it!.
We can also make you a PIZZA if you like 1) I am 6'1" tall,.
The server, however, had a lot of instability! Because I still had the "Original Spintray" from back then, I decided to try that since I still had it anyway, and it fit like a glove! I could have dropped my iPad or laptop if I was looking for some savings I found it to be much more expensive! The Original Spintray is the best work surface to spin with on if you want a stable one!.
Even though it seems to defeat the purpose of the whole machine, sometimes I just want to watch (or do) something else while I like the design, but the surface is a bit slick - my only constructive feedback would be that it seems too tidy. Since the tray has a slight incline, anything you put on it is going to slide right off. The solution is to lay a gym towel on it and that creates enough grip for whatever is on it not to slide. Bravo!.