Dimex EasyFlex Plastic P-Profile Dock Edging
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It would make sense, I'd imagine. Screws are used to install the product. It would be okay if there was a pontoon.
There are about 3 inches between the "P" and the "J". There is a 3/4" tab on the tab
When it bends around a sharp corner, it will pinch up at the top. It will be easier to remove the web from inside, then slice the top part where the screws are located. This is what I did and I think the results were The cost of 8 corner pieces was too high for me.
It probably will, but it will have to be installed with screws about every 6"
Selected User Reviews For Dimex EasyFlex Plastic P-Profile Dock Edging
I expected the product to be great, it is even better than I expected. Unfortunately, the roll-out has not gone as planned The up-side of packaging is that it makes installation difficult and results in poor fit and finish. Nearly 2/3 of the way through After going 1/4 way down the roll, the thick/tough material has reattached to the roll The radius of the fins is so small that working with or installing them is an extremely challenging undertaking. In the case that you can muscle it straight enough to anchor, you're left with ripples on the upper edge that are There is only so much I can say - Although the term finish could smooth out to a reasonable level after some weeks (in this instance), I cannot imagine it smoothing out on time for a home showing. Thank you for reading. I hope this will help.
All three rolls of film are returned. There is an off-centered flat layout in the image. The coil was rolled into the shape of a rectangle. The coil was twisted and not flat when it arrived in the box. In spite of attempts to stretch it in the sun to flatten it, it did not flatten. The dock I have does not fall under this regulation. A total of three rolls were ordered. The order was shipped in three separate In all three cases, the problem listed above was the same. Each box was open upon arrival as well.
It is a great buy and a great product. It is perfectly suited to It is 8 feet long and used as a rub rail on the bow of my pontoon boat. I find it to be professional and organized. The first thing that you notice is the stiffness of the product. You can install it in about 15 to 30 minutes after it's sat in the Sun for a few minutes. It is something I would buy again if the opportunity arose. It has been a pleasure doing business with you.
After reading reviews, I was hesitant to purchase this since the edges did not seem to be Although I considered 8' strips for our covered dock, they are outrageously expensive. I ordered black for the According to other comments, they will arrive in a box wrapped up in a coiled state. For a lot of the components I placed them in the sun for 15 minutes prior to installation, and there was no problem. You will need 2 people, one for pulling the joints snug, and one for installing them. Although you won't get a 100% flat edge, you will get In a few days, after the hot sun heated it up, the grass really began to lay It is essential that you use a top and bottom screw and that the second person pulls it snug so that there is no problem.
I had been searching for something just like this. The bumper is made of heavy-duty material and is made of high-quality material. My only problem is that it looks terrible after installation because there are ripples in the top mounting strip, which happens to be the most visible part of the whole piece. I tried straightening it by padding it with boards but there is still a ripple in it. Probably I'll have to find some sort of rigid strip to mount on top of it to hide the annoying.
I purchased two packages of 25 foot lengths of dock edging . I damaged the dock edging on my 16' Lund fishing boat after it rubbed up against it less than one month after it was installed. After I had replaced the edging of the patio with this Dimex product I noticed that the edging had been in service for over ten years without In order to repair this section of 10 feet, I need a 25 foot run of edging. However, I am concerned that more damage may occur in the future due to the 10 foot section.
They were unrolled and left in the sun for a couple of days until the weekend, when they would be installed. I was able to straighten it This product is very easy to install, cut, and work with. It is important to keep the screws from being overtightened as this may cause them to.
I used this black edging to refurbish a dock and used 200+ feet to edge the deck. With stainless deck screws and cup washers every 5 inches, this product is easy to install. Hopefully, it will last for years to come. In addition, the price is reasonable.
Related Products For Dimex EasyFlex Plastic P-Profile Dock Edging
