Seachoice Gas or Diesel Marine Fuel Electric Sending Unit Kit
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
There are no ideas in my head! My boat was put on it! How many volts does 12 volts have
Float 1. It is oblong in shape. The width of this page is 290. The thickness of the slab is 625mm, and the depth is Please do not hesitate to contact me if you have any questions.
You should look for one rated as low as
It can be set to operate with any tank in the range of 6 to 18 Using the included instructions, you can accurately measure the depth of the 12th cylinder. On our website, you can find details in the technical data section.
Selected User Reviews For Seachoice Gas or Diesel Marine Fuel Electric Sending Unit Kit
This is a very high quality product. Five of the most commonly used features are there There is a hole pattern in the panel which is not evenly distributed, which makes you only be able to install it There is an empty type coupled with a full type coupled at 30 Ohm. Due to my Massey Ferguson 135 tractor gauge being designed for opposite values, I removed the plastic cover, reversed the resistor plate, and then reassembled it. It is a very simple process. As a result, the gauge is happy. The measurement is now 247 ohm "full" and 30 Ohm "empty". The designers deserve a lot of credit for helping to make this possible as well as for their I like the fact that both the inside and outside of this item seem sturdy and reliable.
Does the job. As a result, it was easier to install this fuel sending unit than to remove the old one. It was more difficult than it should have been to remove the old sender due to a limited work area and its construction. Using the new sender is easy you can modify it to fit your tank according to the instructions provided. It was a cinch to reuse the screws from the old sender since the ones in the new unit proved to be too short to make an assured, snug fit into the tank's holes.
This sending unit had been faulty, so I purchased it to replace it. While the order arrived in time, it was difficult to remove it from the plastic packaging that was vacuum-packed. As far as it was concerned, the sending unit itself looked identical to the Moeller it has replaced. I prefer the phillips head bolts since they are easier to tighten than the ratchet ones that came with the sending unit. I think the key thing to look at is that the bolts that came with the unit were just enough to cover the length of the gasket and the unit itself, To end up using the old bolts, I had to use them. As a result of the Moeller unit taking much longer and causing me to regret purchasing it, I bought this one instead.
The packages are sealed when the product is delivered. In my expectation of a whoola moment, I installed it. I began to search for breaks in the wiring, but to no avail. I ordered and installed a new fuel gauge. Not a single thing has happened. My Ohms reading in and out of the tank are both zero. The result was several wasted hours. There is no way to return it because I threw away the packaging. I got a different one. Might be great for other people, but it's not for me. I wish you good luck in your endeavors!.
I am merely expressing my personal It is a bad design according to me, and here are the reasons for that. As part of my repair work on my Bayliner, I installed this unit in my gas tank. It is in a place where I have now re-installed a vent pipe I was able to floor the boat but the sending unit is half under the surface of the floor and cannot be removed. Being honest, I had no idea that I would have to remove it. This unit proved to be unreliable after a day spent riding. After the screw on top was miserably finger tight, it eventually vibrated loose, the weighted design of the screw fell into the tank as it worked itself loose. Having a half-open has given me an opportunity to see new things A ten-inch hole in the top of the gas tank that I had to fill with epoxy and a gas gauge that doesn't work in a tank I might have to cut up the floor to get out.
My boat was missing a fuel sender, so I purchased this to replace it. When I trimmed the rod to fit the depth of the tank, it worked perfectly and was easy to install.
This is an excellent sending device for marine fuel tanks and is very simple to utilize. I installed one in a 16 inch tank and this has enabled me to display the fuel level on the display.
The parts worked and fitted perfectly. I found them to be the perfect replacement and they work perfectly. My sincere thanks.