Talley Tikka T3 and Tikka Master Scope Mount
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
It has a synthetic stock. The gun is a Tikka T3 Lite. All that is left is for us to determine how large the objective bell on your scope is. The Leupold VX-70 I own is a great scope There are three things to do The size of the image is 5 X 10 mm. When I ordered the medium, the regular rings that came with the rifle (a promotion at the time) were not quite enough to allow for As for the mediums, I can tell you that they work quite well. The scope is at the correct position for my eye, and every shot is right where the crosshair is. This is the method for figuring out what size rings you will need. As you describe it, it appears more complicated, but it is really rather straight forward and straightforward - In order to determine the outside diameter of your scope's objective bell, you need to know the outside diameter of that It must be AT LEAST 1/2 of the measured height above the barrel for the bottom of the rings to be acceptable. As a matter of convenience, I will say it is 7/16" with the base and barrel you have but I am not sure what the exact diameter is with yours. To get half the outside measurement of the objective bell, subtract that number from half the diameter of the outer measurement. If the rings are to clear the barrel, they must measure AT LEAST that many millimeters from the top of the base to the middle of the ring. It is the minimum number that I can think of. You may want to add 1/8" or more if you are adding a flip cap. Talley's website offers these measurements, according to my research. In my case, I found the medium bases to be ideal - Though I am confident the high bases can clear virtually any scope, I can't speak for the other. There is only one question - whether or not the scope will be too high for you to see through. Best of luck and good luck on the range.
Neither a rail nor a base are necessary. In order for the mounts to be fitted to the receiver, they must screw directly in place. Does the receiver of your rifle not have a hole drilled and a tapped hole?
My opinion was the same as hers.
A low level. In a nutshell, they are. The distance between the base of the scope and the bottom is 5 inches. This is the first time I've mounted a 4x4 The 40 Leupold that my dad has mounted on his T3 is excellent. It was excellent to have Low on board.
Selected User Reviews For Talley Tikka T3 and Tikka Master Scope Mount
This is the second set of low & high mounts I purchased In the middle.
I work with a Leupold 4 spotting scope. On a Tikka rifle, the optics are 5x14x40mm. When the 40mm Scope is positioned on low and medium, I have plenty of clearance. I have some advice for you In order to keep the scope low, I wished to limit it as much However, I did not get a good view through my scope because the low mount was too low for my liking. Again, there was plenty of clearance with the mediums, and the scope found my eye much better this time.
A Bushnell 6500 2 is mounted on the mount. A Tikka T3 armed with these 16x42s will look fantastic. It is my fifth or sixth Talley set that I have used over the years on different rifles, and like every other Talley set, these are fantastic. * Why then do I give this product only 4 stars? The manufacturing tolerances are perfect.
How then can I give this product only 4 stars? My definition of "low" is nowhere near what these are. There are 99 years left in my life. I am 9% sure these mounts are high enough to mount a 50mm scope or larger In the case of the 42mm scope, there is a lot of air between the barrel and the It seems to me that a 'low' ring should be too low to mount a 50mm scope on top of (even a 44mm will be tight The Talleys are way, way higher, and it is almost impossible to find specifications on what size scope these are suitable for (they used to publish a wonderful chart, but I cannot find it any more). It would have been better if I had This is the low All that said, these will work well enough to prevent me from shipping the extras to be swapped for these, and will save me the time and money of doing so This is low. The fact that my scope is higher than is absolutely necessary is not a deal breaker either, although it is not my preference. It's a 5+ rating all the way for Talley rings. The only exception is if you are placing a sub-heading If you plan to use a 50mm scope on your rifle, get what's extra-wide When you're used to a 1 inch scope, you may think of 30mm rings as being low, but nothing could be further from the truth.
I purchased the low option, and my scope fits perfectly with the scope cover The scope I have is 4x16x44, and I have still plenty of room after adjusting for eye relief. In order to mount, I used a bit of removable loctite. The above options work better than the higher dollar options I've thought of. We are certain you will not.
It'd be a shame to go without the best. Light, sturdy, and well built. These are more expensive than other options, but if you want to open a package, turn a few screws, and expect everything to fit without having to fiddle with something, buy them. They don't seem to move in the rings under recoil (I have one pair on a 338 Win Mag) and they just seem to stay put. This is a good ring to buy if you want good ones!.
The Talley rings I have on a number of my rifles are just as good as all of them. The installation is rock solid and easier than ever. This is on some heavy recoiling rifles (300WM, 7mm RM, and 270WSM) where none of them have moved after a fair amount of shooting. My latest upgrade to my tikka was to install an Athlon Argos BTR6 The 24 x 50 format and the medium are both good choices. It's been over 10 years since I had to lap or shim any of my Talley rings, but I still don't shoot more than 1000.
The front of my Leupold 50MM scope is larger than the front of any of my other 50MM scopes, but medium height rings work fine.
When it comes to my rifles, Talley rings have been almost exclusively used. If you have more screws and parts in your setup, there is more chance that something can get lost and something can appreciate that these are made specifically for a specific model of rifle and that this eliminates the need to separately purchase Just level it up and use the Loctite blue to make it permanent. Talley is my set of choice for many years, and so far I have never had a bad set or issue. I think that all rings should be lapped to ensure maximum ring-scope contact, no matter the manufacturer. But I do lap my rings to ensure maximum ring-scope contact.
An eighth inch of space separated the bell of the Tikka from the barrel of a Leupold 50mm objective scope when the medium height was used. The mount is lightweight, relatively strong, and easy to install by comparison with most mounts (half the number of parts). If you are going to mount a heavy scope on a hard-recoiling gun, then you may want to consider a lighter steel mount. Talley single pieces would be my first choice for a scope mount if it weren't for the price.
Related Products For Talley Tikka T3 and Tikka Master Scope Mount
