Voniry Soldering Mat 500℃ Heat Resistant Non-Slip and Non-toxic Odorless silicone repair mat for soldering electronics assembly or electronics and circuit board repair
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I do not believe that the situation is antisemitic There's no static dissipative property, and I don't understand what "static resistant" is supposed to mean. are no grounding cables attached to this device. It would not matter if there were no particles in it since it is such an excellent insulator.
At the moment, there is no picture of a grounding wire. This mat does not have one This material is conductive and insulating. It wouldn't matter if you connected a ground wire to it. It is not ESD dissipative. These silicone insulating mats are being sold for electronics repair by almost everyone. Look for a mat that contains a resistance between 10*5 and 10*12 ohms per square meter. Ohmmeters do not generally go high enough, and you cannot simply insert the probes into it, so testing it isn't too easy. Here on Amazon, you can buy an ESD mat tester for about $40 that is reasonably priced (relatively speaking).
Magnetic areas can be found in three places on this silicone mat This area is more versatile than others due to the screw storage area, welding pen storage area, and soldering iron storage area. If the back of the mat is clear, you can see which part of it is inlaid with magnets, which helps you determine exactly where the magnetic area is located You can learn how to use it by placing it in the middle layer. Screws and general screwdrivers can be held in the magnet areas, but not by large screwdrivers, but that is suitable for what you need for now. To the left, there is a place where screwdrivers can be placed.
I am glad you asked, this mat is 100% silicone with a non-slip surface The static and insulation functions of the wall. Soldering and repairing family electronic devices (pads, phones, computers, hard drives) is quite simple with this device.
Selected User Reviews For Voniry Soldering Mat 500℃ Heat Resistant Non-Slip and Non-toxic Odorless silicone repair mat for soldering electronics assembly or electronics and circuit board repair
In general, the mat works very well it is thick, so you can use it with confidence knowing that you will not damage the surface whilst using Basically, don't think you can do anything with it in terms of metalwork Since the primary purpose is for electronic use, it is not a good idea to leave your iron on it as it may be taken. You can still burn or cut it if you are leaving the iron on it for too long, so it is heat resistant but not designed to last forever (and then you have bigger problems than just burning a mat, but let's not get ahead of ourselves). They do not stay closed
They have flaps on the tops of the containers, but they do not stay closed Nevertheless, I'm not bothered since I'm happy if there are different areas in which the screws can go. The only way to keep screws from flying out is to place flat magnets under the mat so that they stick all over it. However, there are no small magnets anywhere so I replaced them with flat magnets that stay in place. Mat which can be used for most of the work done at home and in the lab If you need to repair electronics, solder, or build a model kit, you can use it. There's a smell to beware when you open the bag for me it took about 2 weeks for the smell to go away, and I smelled all over my lab (which is a decent to medium sized.
Whenever I build or repair anything, my mat comes in handy, especially when I have small, really tiny, or super hard-to-reach items to reach Within a mile A number of invisible components are The separate areas on the mat for screws, parts, and tools are really nice. In my opinion, there are only 2 things that could be improved There are two things you should keep in mind. It is not possible to close the lids on the three "storage bins" at the top of my mat. The tape normally holds them temporarily closed, but if I need to secure them permanently, I might use some sort of magnetic or velco The second point is
I love all the compartments, so the mat is pretty flexible - but with the walls of the compartments it keeps from rolling about- The short sides of it roll up very well, so I have to roll them up across their width if I want to transport them. I don't believe this is a big deal While this makes it difficult to fit in my portable repair kit, it does make it possible to remove the breaker. The large mat fits my needs so well that I am probably going to buy a smaller version for my "Go.
As long as I had an alligator clip, I was able to fix the problem, but for 20 bucks, I was expecting a bit more. Although the storage compartments for small screws are a nice touch, I wish the work surface was a little larger. Due to the fact that it had to lay on top of a screw storage compartment, my ATX motherboard hung off the edges. If you have a smaller form factor, it should work fine. Soldering is a skill that I use for my smaller projects from time to time. This is a good mat all in all.
I am in love with Those items protect my table top from being damaged by chemicals and the soldering iron. Many parts are magnetic, so there are lots of places for small parts to be held. Almost everything that I solder is very small, which meant that I was constantly dropping bits or having them roll across I no longer need a mat to see anything - everything stays out in the open. It's also extremely easy to clean, just wash it off in the sink and you can get rid of all the flux residue on it, etc. The mat did smell funny at first, but it was fine after an hour of airing out. I may buy another one for my.
These would have been perfect gifts for my friends and family if I had bought them sooner. Apart from its heat resistance and static ground feature, this pad is full of divots, magnets, and little boxes that can be useful in the field. Those tiny SMD components are hard to keep track of and they love to fly all over the place with The solution to this problem has helped me a lot. The component leads I cut off were added to one of the "part boxes" to use as solder traces on the prototype boards. It is essential to get one of these when you use hot air because other things like cutting mats, for example, will warp immediately.
These would have made soldering a lot easier if I had known about them earlier as it's been more annoying than it should have been. With my iron, I can just put it down wherever I want and not worry about it. Having little parts bins is a nice touch, and it beats the Tupperware I used to use.
When I need to quickly solder something in the middle of a busy workday, I cover my desktop with this mat. Fortunately, my keyboard is safe and I can use my headphones An illustration of the product's size can be seen in the picture.
What it should do is what it does. If you're into electronics repair or if you're a hobbyist like me, then this is perfect for you. For soldering, and for some other minor electronic projects, I used it a lot. I enjoy how it helps organize my work desk because it has compartments to store things such as tiny tools, screws, etc. So far, I'm satisfied with the material as it seems to be durable enough to handle the heat of the.