Posi Lock 110 Manual Puller, 3 Jaws, 20 tons Capacity, 9-2/3" Reach, 1" - 15" Spread Range, 20-2/5" Overall Length (3-Pack)

There are many things to admire about this The best of the best Tool for converting HD video to HD. Having helpful, friendly customer service is a big plus. The problem I have is that the plate I needed to remove is 14" in diameter and there was no way I could easily get the jaws wide enough to do the job. That's very true. Although the jaws sat well above the plate, it was too long for the center screw, so the jaws sat above the plate. Please order an extra long arm. I think it would be nice if they provided a planning guide to help you line up the job with the puller and made the extra long option available as a separate model. This is my first attempt at it, so I hope it is successful. We have spent a lot of money on this.

Lincoln Savage

| May 08, 2021

A copy of this was bought by This thing is a total beast, if you can't get a shaft out of a bearing or hub, you may have to torch it. Thanks to this tool and the "hub shocker, tool," our shop has never ran into a wheel bearing it could not This is an awesome tool if you live in the rust belt and you turn wrenches. Makes easy work of freezing axles to hubs and bearings. Also used on a few frozen rotors and rotor rings. These drums are quite heavy and very well-built. Replacement parts are easily.

Lilianna Hickman

| Dec 04, 2020

There were some stubborn pulleys that needed to be removed, but the process was significantly safer than using It was nice having this pulley remover when I removed a pulley a few years ago. I used regular "cheap" pullers in the past. This pulley had a much higher capacity rating than the cheap ones, and it can be locked onto surfaces without coming loose. There have been times when pieces went flying when they moved a little in the press. It was able to remove a pulley that the press was unable to, so I am happy with it even though I have never previously spent this much on a hand tool. Furthermore, I did not have to go to town to pay at the local machine shop and additionally, it saved me the time and hassle of having to wait a couple of weeks for them to finish because they're normally a few weeks behind.

Jovanni Greene

| Aug 08, 2020

This is the best way to remove the 22 inch spoke flywheel on a 5HP Fairbanks Morse hit and miss antique engine. I saw on oldiron some one used it for similar purposes.

Kylan Richmond

| Jan 24, 2021

The purpose of buying this item was to remove the brake rotors from our Sonatas which seemed to become welded to the wheels. When I used a dent puller to dislodge the rotors in the past, I had an easier time as opposed to this last fall when the challenge was much greater. I tried U's idea It was a challenge to screw and nut the tube, but it Although the Jaw Puller was a bit expensive, it would have been far more expensive to take the car to a brake shop. It really worked the first time I used this puller - thanks! The torque should be kept at 20 to 30 rpm while the speed is slowly increased The length is 40 feet Weight loss with lbs proved to be excellent. I also succeeded with my second attempt, but this time was not as gradual and I was much more forceful, leading me to break the rotor first. The conclusion is Put penetrating oil into the rotor/wheel mount interface, and then The length is 40 feet tap the rotor with a hammer to prevent it from popping off the side. To keep you from getting bored, you can loosen the bond between the interface and do it so that you aren't Wishing you the best of luck!.

Ainhoa Bullock

| Sep 10, 2020

A great pulling tool that can be used to remove sprockets safely from small tracked machines.

Daniella SINCLAIR

| Feb 16, 2021

Investing in a tool like this can be a good investment when you need a durable long lasting tool.

Grayson Clayton

| Jan 27, 2021