Focusable 980nm Infrared IR Adjusted Laser Dot Diode Module 3V-5V with TTL 0-15KHz 12x30mm
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
That will work well if you do it
The temperature at which a heat source is contacted (the surface area of the heat source) determines the cooling rate. By the age of 20 To keep it cool at 45mph, the question is whether there is sufficient wind flow to provide enough radiational cooling over the case. Answer the question in the simplest way possible I don't know we would need to test with a temporary. It measures measurement.
Even though I did not receive this product, I understand that it can be configured properly with proper drivers. There will be a pop when the balloon is blown
Spec sheets for the optics used would need to be sent to you as the beam has adjustable collimation.
Selected User Reviews For Focusable 980nm Infrared IR Adjusted Laser Dot Diode Module 3V-5V with TTL 0-15KHz 12x30mm
Both of these failed as well, so it looks like both I received the first one shortly after receiving it and I now own the original. br>br>Too bad for you! A brief update This is not a reliable product, do not buy. *-* *-* ------- There was a dimming of the laser dot after the device stopped outputting any light. It is similar to the first one purchased a few months earlier, but the projected dot has a lot of artifacts. It has many artifacts in the shape of a square and is oval in shape. There are also many artifacts in the dot. At its smallest size, the dot is as small as 2 feet and cannot be focused finer than that at 80 yards. It is not useful as an IR laser.
a 3 inch laser diode operating at 980nm, with a rotating lens for focusing, the diode is In an environment of 0 volts and a distance of about 5', the smallest dot I could produce was about 4 inches In the same manner, I was able to catch the targets with a light source and a small lens from an old BB It might have been in the description that I misunderstood. It will be interesting to try some TTL control with an Arduino Nano and a Level Converter, but I have a feeling that it will just modulate the power output by pulsating on and off the diode. Please let me know if you have any tips for narrowing the "Dot" down to 25mm or an inch at about 5 feet. I was hoping for something similar to those cheap cat toys you can find at Walmart, but turning the lens either way only increases the "Dot" size. Overall, I am not impressed, as I was hoping for something similar to those cheap cat toys.
The first time I turned on a regulated power supply, it blazed for about 30 seconds at a rate of 4 Hz 50% duty cycle. I tried to focus it, since the lens was almost fully out when the power supply was pressed. A bright splotch of light briefly flashed on, then the screen went black and never came back to life. Your money will not be wasted.
After ordering one last week, it turned out the first one was defective, so I ordered another thinking it might have been In the second instance, there was a few blips and then no flickering. The heat sinks I have on these computers make them run for short periods of time. The garbage they produce is impressive. You will only be disappointed if you choose them.
It is a small laser module that is easy to use and relatively stable mechanically. It has a FWHM line width of 4nm and a wavelength of 984nm. 3. delivering regulated goods and services. When I use 3VDC, this gives me about 25mW. Neither the TTL modulation nor the SSB modulation was tested.
Operate it at 5 V to get the best results. Whenever the voltage exceeds 5, there is a buildup of static electricity, at which point you can be shocked by the laser. It was disappointing to find out that there is no specification sheet. Using electrical components in that fashion would not be a good idea. Aside from that, it works quite well. Despite not belonging to the visible spectrum, you can see it with a smartphone because it emits NIR (near infrared).
I really like the way it works. The red and yellow colors must be linked in order for this to be effective. Viewed well with security cameras, but the photo looks a bit blurry with my cell phone camera. A block must be installed to prevent IR. I think it looks pretty good in my picture. I've updated to A TV Be Gone was used to test TTL modulation. The software works perfectly!.
There is an opportunity for more documentation. It would be nice if there was more documentation.
Related Products For Focusable 980nm Infrared IR Adjusted Laser Dot Diode Module 3V-5V with TTL 0-15KHz 12x30mm
