Electronics-Salon Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA-2560 R3.
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Three of these boards (all Ver: ) were purchased, assembled, and used by me. 1) in the previous year, with no silk screen errors. Perhaps there was an issue that I was unaware of earlier. The pads for the breakout connections to the headers that plug into the Mega board are all correctly identified in the silkscreen, using the same reference nomenclature as on the Arduino Mega, and they're all in the right order. Due to physical space constraints, some may have been perplexed by the placement of the screw terminals, particularly where needed for the break out of the double-stranded wire. I/O connector for a row. Because the screw terminals wrap around the sides of the board to fit those 36 pins into a single row, the breakout pad connections (along with their silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk-screened silk screened IDs) to be pushed further to the other end of the board (especially on the side where the Arduino's digital pins D0 - D12 are located). D21 can be found). That just means the breakout pads aren't right next to the Arduino header pins they're connected to, not that they're labeled incorrectly. To cut a long story short, if the pin identification silk-screening is to be believed, All of the actual connections to the Arduino Mega will be correct because they are screened on the breakout board.
ESQ ESQ ESQ ESQ ESQ ESQ 103- D (Digikey SAM9289-Digikey SAM9289-Digikey SAM9289-D ND - 200-Mouser The Arduino Mega will be connected to the Arduino Ethernet 2 Shield via a 6 pin header (2x3) (10314GD).
There are no single-sided printed circuit boards available.
The mega and the due both have the same size factor. The due date, on the other hand, is a 3. Because the mega is a 5v board and the mega is a 3v board, any circuitry must account for this.
Selected User Reviews For Electronics-Salon Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA-2560 R3.
The device provides a screw terminal interface for the pins on the Arduino Mega 2560 microcontroller card. All pin identifications are readable on the PCB. br>br>A few words of caution: Be aware that there are a lot of soldered connections on this board (172 to be exact), and vertical alignment of the pintails is crucial to being able to plug it into the Mega2560, so plan accordingly. In addition, insulating tape should be applied to the top of the Mega2560's USB connector to prevent shorting against the pads on the bottom of the board.
I bought two more to use for future projects after using one for a project. Silkscreen is correct; perhaps those who claim it is incorrect are misinterpreting it. The silkscreen on the outside of the prototype area and inside the piggyback The back arduino connectors are used to connect the arduino to the computer. Not the connectors, but the signal breakouts. The thru- The holes are not perfectly aligned with the connectors and are slightly shifted. The screw connectors are labeled, and the proto area signal breakouts are labeled, which I didn't notice until I saw the one-star reviews claiming the silkscreen was incorrect. The arduino connectors can't be labeled because there isn't enough room, and they are already standard. By the way, mine is the first version. On Amazon, the images are v1. I'm not sure what the difference is, but silkscreen appears to be the same from what I can see in the photos. If you still believe the silkscreen is incorrect, please post a photo of the problem(s).
The header pins are pre-installed on another version of this same board. soldered. This board, on the other hand, does not, which is a positive. I mate the pins (actually similar header male pins from Digikey) with a MEGA board that also does not have the pins soldered on the top rather than the bottom. These are also available on Amazon. Soldering is a highly reliable method of permanently joining the two boards. These are used in a variety of applications. A fantastic piece of equipment.
The board, as well as the headers and screw terminals, are of very high quality. If I need screw terminals again, I will definitely buy this. br>I took a star off because the package didn't include an ICSPI 6 pin feed-through connector. by means of header.
The slikscreen was printed on. Be careful who you buy from. You'll need to remap pinouts because the slikscreen printout on the PC board does not match Ardunio pinouts. For the price they're asking for the board, you'd think they'd fix it.
I couldn't believe what Robert B had written could be true - It's true that no one else noticed. It's a waste of $20 because the silkscreen doesn't match the pin assignments. The year 2005 was a waste. Soldering takes about an hour. It took me an hour to realize it was worthless garbage.
As expected, the product performed well.
I created a device prototype with this product. It does exactly what it says on the tin. It comes at a very reasonable price. It appeals to my tastes.
Related Products For Electronics-Salon Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA-2560 R3.
