Pro Marine Supplies Crystal Clear Table Top Epoxy Resin & Hardener (2-Part 1 Gallon Combined Kit) with Cups, Brushes, Gloves, Sticks | UV-Resistant Gloss Coating for DIY Bar, Countertops, Woodworking

According to the directions, it melted and hardened. That's not what I expected after that! Protected against UV rays, according to its label. I don't believe it! In terms of thickness, it does not need to be thick to maintain its In buying this resin, I made sure that it is UV-resistant because I wanted it for an outdoor table top. The mixture blended fine (I kneaded it for two minutes on each batch using a mechanical mixer). Hardening took place as expected. There was no cloud cover and the sky looked clear. There was only one thing left to do I finally decided to put it outside and that's when it turned yellow! This is such a dreadful sight. In a letter, I wrote to the company and asked what made it happen. They told me it was being outside and that it is more than 1/4 inch thick. Oh my goodness, thanks for ruining my project such a lot!! This is due to the fact that it was changed! Sadly, everything that will be outside will be affected by this!.

Paola Nichols

| May 30, 2021

They will still deliver the product, regardless of the quality of the batch. The task I was doing was multi-tasking A layer pour that reached a depth of two inches. The layers were cured one after the other over a period of several days to allow for complete cure. In the first picture we see the results after double pours and they are completely I worked to remove any bubbles that rose to the surface before pouring the third pour. The pour was only 1/4" thick at its deepest point, and after about three hours, it was completely clear and beautiful. A few hours later, I checked the pour and found it to be filled with All of these are trapped. It was probably from a different batch of this product as the 3rd pour was from bottles of the same product ordered at different times. Pro Marine customer service asked for details about my pour and said they would review it. I thought I would be getting some responses when they provided photos and their responses. The email I received back from Amazon said, "I see that this order is fulfilled by the company Amazon so it will need to be directed to Amazon. So that they may be able to assist you, I am sending the same information to them. It is not clear which hub of theirs this came from or whether there are any issues. That's the case! In spite of ProMarine Supply Co. fulfilling the order, the retailer was not notified. Amazon managed to get rid of the issue and wash their hands of it. It makes me so sad. You should stay away from this product provider if you want someone who stands behind their product.

I now have hours of work to clean up this mess and redo it with a product that actually works.

Louisa SYKES

| Jun 18, 2021

It's still only a bit more than 20 minutes that I have to work with. It is a good idea to have all your colors at hand So I will try again since I did get good results with my coasters. If you check them once they're done every few minutes, you might be able to catch a few that rose to the top before it gets too difficult. The price is great, but it In the original Even when gently stirred, this got extremely hard. There were tons of bubbles, and it was impossible to get them When I pour my other resin, I pour the extra into another mold like a keychain or something smaller, yet this resin was thick by the time I got finished pouring my set of coasters maybe twenty minutes later. It is best to measure exactly in order to avoid wasting The one I'm working on now does not have any extra clear so I always keep some extra in case I need it to finish my coasters. I will not be purchasing from this company As a result of its lower price, I bought it but I can already tell I'll waste resin with this one due to how quickly A bit hotter as well. I only felt a slight warmth from my other one. The cups were still hot 40 minutes later. I hesitated to throw them away until they cooled down. There's a chance the coasters are good. The coasters look OK, except for the ripple that I'll have to repair tomorrow as a result of attempting to pop some bubbles on one of them. Previously I stated that so many bubbles were there. Then there are the ones that pop when it's too late.

Allyson Short

| Jun 24, 2021

Set up takes about twenty minutes and allows you to have a working product in no time at all Before it gets clumpy, you have 30 minutes to work on it. When I was doing a project, I sometimes forgot to leave a small amount of epoxy in the mixing bucket, just in case anything came up, and less than 15 minutes later, every drop in the bucket had.

Angelina McGee

| Jul 12, 2021

The other stuff I use was out of stock, so I bought this. The coasters that I make for cars are custom made. As I would normally do, I mixed and placed under the ultraviolet lamp. In an hour, I let it sit and it did not harden at all. I will not buy this product.

Piper Jarvis

| May 03, 2021

The resin does exactly what it should.

Kai Rodgers

| Apr 13, 2021

It's more for small and simple things. It is not often that you get to play with epoxy of this type. My personal taste does not incorporate several different looks at the same time. Getting hard and caking up quickly was the result. In order to get the epoxy out of my panel, I had to pull chunks of it. There was also a low level of flux and movement in the epoxy that caused color to blend together.

Diana McCann

| Nov 08, 2020

Resin of excellent quality. The resin I use is for decorating with ocean waves and making small resin sculptures. It can be used within the indicated times and if used properly, will catalyze. Shipments are delivered quickly and on time. There is no better way to spend your time.

Joseph Frost

| Mar 11, 2021