NORTON 07660788263 (38A) Premium Alundum Type 01 Bench and Pedestal Grinding Wheel, Very Fine Grit, White Aluminum Oxide Abrasive, 1" Arbor Hole, 6" Diameter x 1" Thick

Thanks to the Raptor R3X bushing, our car works perfectly! The reviewers wrote negative things about this book, so I searched for answers and I strongly believe I found them! There is a product called the Raptor R3X Grinding Wheel Bushing 2 Piece Set that Craft Supplies USA sells. You can order this flange with an attached bushing in either 1/2" or 5/8" sizes for use with motor shafts up to 1/2". in two pieces, with the flange with the busing all in one piece, and another flange for the other side (which I did not use, but used the original grinder inner flanges). I ordered a 6x1x1 wheel, but the bushing will fit an 1" wheel without problem (the wheel I ordered is 3/4" long, 1" wide). My 1920's grinder suffered from the past owner using only big washers as no flanges on the outside. Today I purchased two sets of these flanges from these suppliers. When the Norton wheel arrived, I was ready to go, having ordered both sets and the wheel as soon as they This is exactly what I was hoping for! It was not worth wasting time with the plastic bushings that were supplied because it appears they are not the best. So I removed them and replaced them with my new Raptor bushing flange, then I The format might be 1/64 inches). I am amazed! I am very pleased with the results. With respect to shipping, I ordered just the wheel so it would be all that was in the box from Amazon and wouldn't bump into anything else. This was sent in a box similar to the ones Amazon uses for delivering books however, there was little room for wiggle. was in perfect condition when it arrived. There is no doubt that the Raptor R3X Grinding Wheel Bushing 2 Piece Set is the solution. If you buy a good bushing, it is worth spending the extra money, but you won't have as many issues with any grinding wheel you buy that comes with a plastic bushing.

Messiah Gordon

| Jul 28, 2020

tried to install this wheel for the first time, it was very wobbly and vibrated a lot. Wheels do not cause this problem the bushing does. In addition, the plastic bushings did not clamp tightly on the shaft, which caused it to be out of balance. The bushing I found is This is com. ). The Raptor R3X Grinding Wheel Bushing 2 Piece Set 1/2"
1053500001 costs It cost $17 to send 95 to 1. I would have never expected that 95 would make such a There is nothing wrong with the six inch grinder, but I don't have I was so happy to receive this. Having sharpened all my tools with confidence now, I feel more confident about using them.

Arya Shea

| Jul 29, 2020

There is no better wheel than the Norton As for the wheel itself, it's fantastic I know your motivation, but– There are plastic arbor inserts in this kit that are extremely low-profile In my opinion, tolerance is essential. In this case, you will not be satisfied if your grinder has a 5/8" or 1/2" shaft. It is HORRIBLE to feel the wobble and vibration! Make sure the arbor you purchase is compatible with your purchase Unless you have an arbor that is 1" wide, you can't use this. Edit and rewrite As far as I know, I can dress the wheel true- It will be up to me to take care of it Nevertheless, it is disappointing how much extra time and effort will be required to perfect.

Valeria Palmer

| May 07, 2021

I found this wheel to be very efficient at removing materials as well as staying As I didn't want to trust the plastic bushings that came with the kit, I used stainless ones instead.

Averi Chung

| Jul 23, 2020

It is a total waste of time and money to use this grinding wheel. The paper is out - The center) by more than 1/4". I tried to dress it on the grinder, but it vibrates so much that it loosens In view of the Corona virus situation, I doubt that I will be able to return the product. It may end up on my lathe so that I can set the speed low to true it up.

Naya AHMED

| Jul 17, 2020

The wheel needs to be dressed before each use, but that is something you will have to get used to regardless of the wheel type. Despite the fact that it was damaged, it arrived with the needed bushings. It is not a major media outlet today (unlike today's media Is that right? as well. It's hard to argue with Norton when it comes to their.

Theodora Frey

| Apr 17, 2021

There was so much imbalance that the grinder wanted to fly off the bench when I put it on the bench grinder. There is no need to worry about bushings and fitting I'm not sure whether the bushings are too soft or wrong, or if the wheel is just a bad quality. But now both wheels on the grinder vibrate, causing the workstation to become.

Kaydence Jefferson

| Jul 24, 2020

The first 3 are broader than the second The grinder comes with four stones of this size. My Craftsman grinder still works with this shaft. This stone is excellent for blades, and it does a good job removing fine grit.

Ayaan AKHTAR

| Mar 19, 2021