Modway Attainment Vinyl Drafting Chair - Drafting Stool With Flip-Up Arm in Black
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
I bought four of these chairs for my high dining room table and responded with 25", so I pulled out the measuring tape, lifted the chair as high as it would go, and it was 25", but I sat in it and lowered it all the way down - and it was 22". Having reached 22", I lifted it back up and was delighted to discover it is 30". In my review, I said that it is as good a chair as is expected for the price, but that the cylinder is still a little bit stuck. As a result, I'm sorry for my error in my first response, the correct range is 22" to 30" from the floor to the top of the
There is no doubt about it. There is a ten-inch limit to the height of the foot ring above It is a bit challenging to use the foot rings when the seat is all the way up for me as I am 6'2" and 10".
There is a 22-26 inch range of height for the seats My chair just arrived, so I measured it right away.
It measures 18 inches in diameter. Sadly, it is too small for a 24 inch There is also no usable space in the rear region of the seat since the back support sticks out. Although closed, the design is not up to what a good seat should be like.
Selected User Reviews For Modway Attainment Vinyl Drafting Chair - Drafting Stool With Flip-Up Arm in Black
I WOULD BE APPRECIATED IF YOU READ THIS. You may notice your chair sinking when you sit in it at a high angle I had a new chair for a couple of years, but I always found it impossible to get it to hold a high position even when it was brand new, and the situation has gotten worse over time. It is not possible for me to weigh anywhere close to 330 pounds for this As a result, we took apart the chair to see if a new cylinder could be installed. The answer to this question is 'NO, it cannot be replaced'. I have noticed that after we put the chair back together, it is no longer ARE YOU SURE? The reason behind that is beyond me! Upon taking the cylinder portion off of the chair, we discovered that the oil inside the cylinder was in fluid state and moved around inside the cylinder. The lubricating oil soaked into the seal of the cylinder and caused the gas to leak out. Moisturizing the seal made it more able to hold Hence, in order to prevent sinking in your chair, you should turn it upside down for a couple of hours so that the lubrication oil is able to drain down to the seal. The moment we realized that we could not fix the cylinder, I had to buy an entirely My new one should arrive tomorrow, now that my old one is working just fine. I hate it! I just wanted to mention It is wonderful to sit in this chair now that it is repaired! I like how it feels and how well it holds up.
Working from home full-time has been a great experience for me For around a decade, I have been working full time. The chair I'd been using for the last six years has gone through a fair amount of changes. I recently switched to a sit-stand desk because it worked better for me Stand desk that can be programmed and is The reason I wanted a drafting chair was to keep me at seated height even when standing, as well as to make the transition smoother. I settled on the Modway Attainment chair after doing some research. There is much to be positive about There are armrests that can be lifted out of the way, and I like that. The reclining chair responds well to adjustments and moves smoothly. There is no doubt that the price is fair. There are three things wrong with this I have never owned an uncomfortable chair of any kind, it doesn't matter what type. understand why, but I'm feeling a lot of pain in my butt, lower back, and upper legs as soon as I sit in this chair. I bought a $30 memory foam pad to try to salvage the chair. I found it helped a bit, but it only delays the acute pain by 5 minutes at most. In my present state, I am seated in a $30 Ikea chair that doesn't require any adjustments, and I am It should be clear that this chair is not a good one either, so I'll be.
The chair is not the best available on the market, but it is a good value for the money. The height can easily be adjusted in a range of 10 inches and it takes about 10 minutes to assemble. As well as folding up, the arms can be kept out of the way when not in use. It is very comfortable for me to sit in, and I can sit in it for hours without experiencing cramps or issues with my back. Although it does not seem to be of the highest quality, it is also not badly made. It should last for several years, so it's definitely a good investment.
Initially, when I assembled it, it was quite tall once it was extended to its full height, however, soon after I started sitting on it, it started sinking. Once it's in, you can't ever get the pneumatic stem out again, so I tried to send it back. The pneumatic stem simply slotted into the bottom of the stand, and once it's in, it's impossible to remove. Persisting in hope that it wouldn't sink any further, I kept trying to keep it upright. Currently, it is too late to return it, and the height has been sinking for some time already. Now that everything is in place, we can move forward There is an extended height of 28 inches, which is well below what I need and is a stumbling block to me.
A comparison of the pros and cons. The pros are I received this yesterday, it was delivered on time. The chair is excellent. My lower and upper arches of my back fit perfectly in the seat and back because I am 5 feet 1 inch. There is very nice padding in the seat. It is very comfortable and there is plenty of room for movement. In any case, it will be very easy to cover if the fabric does not last. My shopping is organized by purchasing items together, so it was easy to set this up. There are some cons to this I must contend with that however. It needs to be proofread and you need to add a few missing steps for someone who may not have put together any products. wish the loop on the rod of the chair had been a little bigger (since I do not have long legs I am one of us "shorties"). It is designed to be used for using it as a foot prop while sewing, rather than turning the chair sideways. Great product all in all!.
I was able to fulfill all my goals! Months ago, I read so many reviews, comparing prices, and shopping for several months. Thanks to this chair, I feel as if I've won the lottery. It goes from being a normal height adjustment to a very tall one! My foot stool can be positioned further away or closer to me, and the arms can be moved, if necessary. Seating is extremely comfortable, and the angle is just right. Mesh back offers great support, and the chair is designed in an extremely sleek manner. The material appears to be very durable too. It appears that the wheels lock in on the top of the base with a tiny scratch. At a distance, however, it is not noticeable. The steps were very easy to follow for me to complete by Once my husband got home from work, I asked him to tighten the screws one more time. With my 5'2" height, I have my desk on risers so that I can stand at it. Unlike my other chair, it did not raise very high. the chair I bought is perfect for a home office. My only wish would be for the round footstool to be a bit bigger so I did not need to tuck my feet in to sit The footrests are all about the same size, so I believe it is standard size.
unpacking to complete assembly, it took 45 minutes. I was pleased with the quality of the chair, but the pneumatic cylinder went down from its maximum height of 30 inches after I sat down, so now I am unable to comfortably type on the keyboard. * I also do not know how to tighten the foot rings? I don't think a three out of five is fair, a four is way too much and a five definitely isn't fair. It's true that the arm rest can be lifted up for easy hopping on and off the chair. However, I would rather have the arm rest adjustable up and down. My Lexmod issues have been discussed, so I will wait and see what happens after I get back to them.