12" Boil Screen 1/2" NPT Fitting
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
You are right, that is Directly attached to the pot/mash tun's valve inlet, the screen tube works as an air filter. Filters the mash after it has been blended. When this is used, there is no need for a false bottom. I liked it a lot!
Make sure you have an adapter that goes from 3/8" to 1/2". If you use 1/2" screws, make sure the female side is on the thread. You can find this on Amazon. You can get it at your local orange or blue hardware store for about $6 for an Anderson Metals Brass Pipe Fitting, Adapter, NPT Male x NPT Female*br>Anderson Metals (15)*br>
The hose clamp is all it needs to hold it in place. Cut it to the desired length would not be difficult. A prefilter before a fuel pump is what I used mine for in a
Hello, this should be installed horizontally across the bottom of the mash tun or kettle.
Selected User Reviews For 12" Boil Screen 1/2" NPT Fitting
In summary, this is a high-quality product. It is sturdy and durable, and with the right care, will last for years to come. It, well, doesn't do that great of a job in this context, as I was hoping to use it as a filter for my wort after boiling. It's hard to tell where the mesh ends and the mesh starts. If the mesh is too fine, then your flow rate is going to suffer, but if the mesh is too loose, then you may as well not have it at all. Despite the mesh being of a decent size, it did catch the hobs/trub/whatever that was in the wort, but it did so too well, because I was able to get a decent flow for about thirty seconds, before my flow It was necessary to sanitize a long handled spoon and to scrape the bazooka clean so that it could still function. The idea is a good one and I'm going to give this a try over my old whirlpool method. Although it did not work quite so well as I hoped, it was still a good experience too. As opposed to relying on it to filter post-boil wort, it is probably best to make this a staple for all grain batches (instead of a false bottom).
Since I could not afford a false bottom that costs 4x as much as this bazooka tube, I bought it. I don't regret it in the least. Since I had been using the local homebrew shop owner's mash tun, I wanted to build my own so that I wouldn't have to continue using it. Then, I started searching for ways to save money when I learned that it cost him about $120 to build his. Considering that this mash tun cost just $58, it is hard to beat. LHBS owner and I brewed the same beer side by side, with me using my mash tun with the bazooka tube and him using his with a false bottom, and both of us got With this mash tun, I have brewed 3 times already and the bazooka tube works perfectly. Occasionally I will put a hop sock over it to filter out small grains that get past the screen, but it is not necessary to do that. My overall experience with the purchase has been positive.
To boil water, the liquid was placed in the kettle, and I heated it up I tried it with 5 ounces of pellet hops, and it clogged completely. I admit that it did filter my wort more thoroughly than I've ever done so, but it was flowing at a rate of 2 gallons per hour when using a pump (I collected 2 gallons after sitting for an hour). The flow rate had to be constantly scraped with the mash paddle in order to keep it going, which was incredibly tedious. As you can see in the picture, after I disconnected the pump and scraped the screen, the flow rate went up You can see that the valve is very The second time I used it, it was the last time. It would apparently be better to do this in a mash tun because the grain bed (husks) would provide an extra layer of filtering and would keep small particles from clogging the screens.
The product works well for what it's intended to do. However, I had to take it out because I found that it worked a bit too Nevertheless, it does a great job of taking out all sorts of stuff from my wort. However, I feel it is a pain in terms of my setup to have to clean it continuously with a sanitized spoon whenever it gets stuck. It should be totally fine if you can get this to work on your brew setup. (If doing brew in a bag, be very careful with the bag that you put into your kettle. It can get caught on this and it's not easy to fix with 20 lbs of grains.
It seems that the quality of the screens now is extremely poor compared to the past, when I purchased the same or similar screens. Welds on a mesh seam came loose after a couple of brew days, if there were any on there at all. SST is also supposed to be used in this In addition to rust developing on parts of the screen, it also seems to have deteriorated over time. In the end, I switched to a DIY screen that works way better, and I would not recommend this method to anyone who has experience brewing.
To make it work you have to open the valve slowly at first. Once the wort has slowly passed through the filter, this should not take more than a few minutes, you can open the valve completely and trust that this filter will come into its own. This is what you see in the The recipe for the Irish Red BIAB is 5 gallons in volume, and there are 3 oz of hops in total Just to assist this bazooka a little, I would use a hop bag instead of a filter or screen if making an IPA. Here's a kettle filter that I strongly recommend.
It works great! Using this thing has cut my draining time by half. My draining time was impacted by steeping bags and other strainers that weren't straining effectively. There were times when I had to clear the screen during the drain, but that was when about 75 percent of it had drained out already. Purchase one and you will not be disappointed.
In order to avoid buying this device, I had been using a homemade cpvc strainer for a few years. What is the reason for this? However, this is much superior to the homemade rig I was using. The wort catcher was easy to clean and did an amazing job catching debris and still allowing wort to flow freely. We have the best bazooka tube type socks, so please do not hesitate to contact us.
Related Products For 12" Boil Screen 1/2" NPT Fitting
