LoveRPi Performance Heatsink Set for Raspberry Pi 3 B+
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
This is 3M's 8810.
The tape does not conduct electricity, nor is it
In addition to the heatsink, only the LAN chip and the SoC are covered. Heatsinks are not needed for LPDDR2 on the back side since it doesn't get hot enough to warrant them.
Without a doubt. The ones I have are on the Pi 3 B+ I use.
Selected User Reviews For LoveRPi Performance Heatsink Set for Raspberry Pi 3 B+
I already had a set of heatsinks with the pi3 package I purchased, so why did I purchase the LoveRPI It would have been better if the performance had been better This was not a disappointment for me. Heatsinks included in the kit I purchased are taller (more surface area = better thermal performance) than those in this kit. Thermal tapes are made by 3M, and they stick well and can transfer heat well (heat sinks get quite It tells you the tape is doing its job well when it transfer heat). It is an excellent purchase for those who want a more efficient heatsink than the tiny ones that come with.
It was easy to attach these heatsinks to my Raspberry Pi 3 as they adhered easily to the SOC chips Using the Pi 3 as my gaming platform, I tested both of them. In retroPie I often got a warning for temperature when trying to load up certain games, so In the case I use, a plastic box from the Pi Foundation that retails for $8, my Pi has no fans, so it works just fine without any With these heatsinks installed, I had no problems. After 30 minutes of solid gaming with the hard to play games that overheated my Pi, it is no longer overheating. As I was able to get them within two days from Amazon, they were worth $4 to me. I could have possibly gained a savings of $1 or $2, but I would probably have to wait 90 days and have them shipped from China, which would mean I would save just $1 or $2 at most, so my pick-up was easy. Thank you for providing a product that was easy to install and solved my thermal issues. . . If I hadn't been gaming or using the Pi for anything strenuous, I would not have had the issues with overheating, but there were a few games that overheated the Pi.
As part of my 3D printer, I use a Pi 3b+ running OctoPi. Often the temperature in the room it's in is in the 70s or 80s because the room does not get a lot of air conditioning. Using 720p video and streaming the webcam video at 20 frames/second to monitor my print, I still throttle sometimes because I get above the CPU temperature that causes it. I'm sure things are better with the heatsink than they would be without it, and in a room with a better airflow or climate control, you could probably do fine with just the heatsink even if you were using your computer quite heavily. The 30mm fan topped things off in my case so that I could keep the system It might useful for someone to consider whether I should buy a fan along with those.
As a result, there is very little difference between this heat sink and the original Canakit heat sink in terms of temperature. Compared to the Canakit heat sink, this SoC heatsink is taller. According to my calculations, both types of heatsinks have the same surface area of the fins. Approximately 784 square millimeters of surface area are covered by the Canakit SOC fins. 1120 square millimeters are covered by the heatsink fins on this SoC. The heatsink on the left has five fins, while the one on the right has seven. In my case with the top removed, there is a muffin fan blowing upward. The tape may be more effective on the heatsink of the Canakit. You could use thermal paste instead of the tape, but there won't be a way to keep the heatsink in place unless you modify the spring to attach it.
As I idle and run my RPI 4, it gets very warm. The overheating and throttling that was occurring in my PC was due to these heat sinks. I installed the heat sinks and found that they brought down idle temperatures a little bit. weren't enough to counter the heat issue with the Raspberry Pi 4. It appears that I found the solution for my computer after removing the filters and installing a Pimoroni Fan Shim. The product arrived on time, was well made, and did what it was supposed to do. My health is just not good enough.
The price is a bit high. This is what I put on my Raspberry PI 3B+. Don't buy heat sinks if you don't know what you're doing. They have a thin 3M type of stick tape coating to ensure that the heat is properly transferred. However, a lot of the heat sinks I investigated had a thermal blanket on the bottom, which actually interfered with how heat is dissipated.
In a plastic case, I bought this to go with a Pi 3. So far, I've used it a couple of weeks and I've had no issues with temps. The peel-offs are these Nevertheless, they are convenient and the only thing I'm uncertain about is the strength of the thermal adhesive. If they last long, they are quite useful. My plan is to buy some thermal epoxy to bond the components permanently if adhesion becomes a problem.
Seagate Barracuda hard drive arrived in the mail this afternoon, and I installed it without a hitch No documentation, other than a Limited warranty (about 3 paragraphs) in several different languages, was included with the installation software. The installation should be done in a particular direction but it would have been nice to know that. This question would increase the number of stars in my review if it were answered.
Related Products For LoveRPi Performance Heatsink Set for Raspberry Pi 3 B+
