Power Acoustik RZ1-3500D 3500W Class D Monoblock Amplifier, Black

A 15-inch Soundqubed sub and a 15-inch Soundqubed sub In order to power it, I purchased a Cobalt 2500 from Orion. I was put in 1D after about 8 months that shot craps on me and began to jump in & begin to play I had to turn off and turn off the protection mode to get it out of protection It's time to move forward. I let it jump into the water for about 20 minutes then it began to jump out. Once again, we are out of protection mode! My next step was to get a I finished it in a little more than a month. This was also the beginning of the same problem! It includes the Razor 2500 and the Power Acoustiks system that I installed on my girlfriend's car. Although I've always believed that top of the line products should be used when it comes to audio systems, I've been installing PA Gothic 12" subs for quite some time. PA has always been just another middle of the road generic brand of audio components for me. Her system continually amazes me with how well it performs, not only because that tiny little amplifier performs so well in terms of sQ and clarity, it also sounds tremendous in the recordings she has done with it. . . In addition to her dual Gothic 12" setup, she uses an overall stereo output. In spite of this, she purchased a kit that had only 8Ga when she installed it. Connect the power cord and the grounding wire The ground on which that amp is running isn't sufficient enough for the 2500w amp to run at 1ohm, but that amp still puts out incredible power and is not very big. I have it set at 3/4 gain and only 3/4 boost There was no non-stop after that Even when I just cruise around town for an hour or two the temperature doesn't change! I decided to check out the 3500 RZR after I had been blown away by the YZ250! Due to how well her razor performs, I am no longer concerned about the blade size the only thing I am concerned with is the fact that there are two 40amp fuses, resulting in 80 in all. A fuse total is normally multiplied by the voltage it is fed. For example, 80Ax13 would be The 9V is equal to 1,112 RMs and & RMS output @1. 0 ohm is usually the closest you'll get to the true value. I. & I. Taking The RZR3500 for example, PA states that it is rated at 2100RMS at 1 ohm, which is a completely inflated figure! In any event, as long as I test it after hooking it up & it does not leak any leakage from it If this amp can perform roughly the 1,112RMS that Ohms law suggests it should I will be extremely happy with this amp especially at such a low price! I plan to install this here in the next few hours, so once I've done it, tune it up & connect it to the internet I will give you an update on this amp once I have done a quick clamp test. Even if it performs half as well as the Razor 2500 my girlfriend owns, I'll be more than satisfied. My bias for Power Acoustiks would definitely be swayed if that were the case!.

Milo Patton

| Dec 25, 2020

Among the issues I encountered was I had to turn up the volume all the way to get the beats I wanted from my 1200 watt speaker system, and there was a loud hummm when there was no music on and I accelerated. Oh, I see. There is no way I could remember. In their email to me, the company stated they were only interested in replacing the product (which would be great if it weren't working), but did not discuss it nor try to troubleshoot any issues. The unit is supposed to handle a lot more power than my two 1200 watt speakers, but it is barely able to keep up. The speakers are good for the money, but I wouldn't recommend them for those with high-end audio equipment.

Castiel Marshall

| May 22, 2021

You have to see what this thing can do! Installation is easy, and it fits almost anywhere thanks to its small size. Power is being supplied to two 10" DVC Power Acoustik P3-based monitors 10W drives and they are effective in ported boxes! Even when the gain setting is set to 3/4 and the bass boost to just under 3/4, these things do not even distort. I'm sure I could push them harder once I get rid of a few trunk rattle issues.

Myles Townsend

| Nov 17, 2020

Basically this is a really good amp for the money, but there are two issues to consider. I have tried to fit 4 gauge wire into the amp, but I have not been successful. You can trim the copper on the end and fit 4 gauge, but what is the point when you have over 8 gauge by the time the 4 ga wire fits. The two other factors are that the amp runs super hard at 4 ohms while staying cold, which has me thinking longevity of this device will be outstanding, but for the price point, I am concerned that poor-quality components will end up being an issue. I hope I am wrong about that assumption because I want this thing to last, and I hope that it will if I run it at 4 ohm cold!.

Sunny GARDINER

| Dec 01, 2020

The situation seems to be fine. In my experience, the 2500 and 2300 dynos are close to its rms specifications. I know these amps are designed to accept thick wire, but why is that the case? My shirt needs to be shaved down by 4g. Unlike the higher power version, this 3500w model only has two 40amp fuses. The validity of that is also questionable. Aside from that. It's really important that you run at least four miles Using your line out converter, you can make power for this amp with the number 5.

Branson Edwards

| Jun 16, 2021

Despite its warranty, Power Acoustik wouldn't honor it. Their speaker melted internally while they were pushing it.

Jude Stephenson

| Aug 05, 2020

The power distribution and utilization are solid for such a small package. I will be upgrading and possibly updating this review. It may be the dollar store Subs that I have. It doesn't seem to be able to push 3500 Watts, however. Since I have two 1600 watt subs, I don't get a buzz in my eyes.

Nico AHMED

| Sep 01, 2020