BAMF 6-Way Coax Cable Splitter Bi-Directional MoCA 5-2300MHz
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
TiVo Mini uses MoCa 2 so I'm using the splitter with the TiVo Mini. As long as I put terminators on all the unused splitter jacks, there were no problems.
There is nothing more to it than a signal The Coax cable should work if you are using it.
It's hard to tell. The box I use is on the exterior. No elements can harm it, and it has been working well for some time.
This is what I used the cable box for cable TV. In total, there are five lines that are split off the main line. The modem has a cable connection and three HDs. For the time being, I have capped one with a 75 ohm cap. The changes are crystal clear and seem to occur more frequently. It was especially important to replace the cable lines on those two.
Selected User Reviews For BAMF 6-Way Coax Cable Splitter Bi-Directional MoCA 5-2300MHz
Furthermore, BAMF's customer service responded immediately to my email, and they were extremely You can find a few of their statements below. It is best to hook all your MoCA devices up to the "Out" ports of the splitter if you are only connecting MoCA devices to it (not using the antenna or cable TV). You won't be able to connect anything to the splitter's "Input", but you should either put a 75 ohm terminator on the input, or you can use a MoCA filter instead. You will be able to perform better on your MoCA. The splitter should also be terminated on all "Out" ports that are not in use.
The fix solved that issue but caused a conflict with Xfinity Internet, knocking my connection off completely and making it impossible for them to access the modem from the command line. If you want to continue getting internet access from Comcast, do not purchase this if you have Xfinity (Comcast). There is no way you will be able to use it. Due to the item being past the return date, I cannot return it. I have to pay.
The cable was run 50 feet to the outside box of my house. The splitter was connected to six cable lines. 30 channels are available over the air on each TV within the home. This is great!.
The old splitter was installed eight years ago it needs to be replaced There was an old sign that read "4-" 10 years ago My new Xfinity cable boxes went from showing one a green bar "low" signal to five green bars "good" signal when they were set to "1500MHz". There was no real difference in anything that came out of this It's not exactly clear what's going on with the cable boxes, but all are running well. They probably won't have to work as hard streaming DVR content around since they won't have to copy it from one place to another. In summary, this was an incredibly affordable upgrade with a strong technical benefit. We used the BAMF 2 Using a 3-way splitter to branch to the cable modem prior to the 6 way splitter TVs must be routed via the way branch. Additionally, unused ports were fitted with 75 ohm terminators. Using these splitters and configuration, nothing but net is being shown on the technical level.
Because this says "all ports power pass", I bought this (along with several other sizes). There's some truth to that, but not all. In my case, I was powering two preamps Using them as combiners with amplified antennas and then switching to another antenna that has LEDs for power - failed - then tried another one with LEDs for power - failed - It is discovered that power can not be reversed by this device. My experience is that it is a quality product, and the one I'm using as a SPLITTER is great my MoCA works well, and the channels I get from a single antenna come through the splitter perfectly. In the end, I ended up spending more money on antenna products as a result of this power-cut There is an issue with the pass. In my search for a splitter, I have found the following All ports of the device are powered in both directions through this connector.
One of the coax connectors on one of them proved very difficult to screw on when I ordered it for a project. Not just for it to go on farther after hand-tightening. My point is that once the threads are properly caught and caught, you can't tighten any further. It was barely on, and I had to resort to a wrench to get it on. I am not too happy with the outcome. On top of that, the white label on the front of it looked In order to snap it into place, I had to press down on it. This, however, was the exception, not the rule. It has been good for me to use this version of the splitter as well as many of the smaller ones. There was something strange about this one.
Please read the complete review for more details. This is a fantastic splitter that allows you to balance the feed to every device. However, it works best when you use the smallest splitter possible, since your main signal is split by the number of outputs, so choose the one that's appropriate For example, if you only needed four outlets or cables, you would install a four way splitter. This will help keep stronger signal to each outlet. Cable switch should be installed near your main cable box, not in the middle of any existing cables.
Wires in every room of our house are already installed to provide cable and phone service. Our cable box is in a different room than all the others because Xfinity decided to cut all the wires. It would be much cheaper and easier to move the router to another room and not pay those ridiculous outlet fees, as well as adding a TV box to Husband put new ends on the cables and used this splitter outside. It has been over a year and it continues to perform well, even in Wisconsin.
Related Products For BAMF 6-Way Coax Cable Splitter Bi-Directional MoCA 5-2300MHz
