Garage Wall Protector Foam Wall Column Guard for Parking Garages - Reflective Wall Edge Protector - 2 Pack Pole Guard - Wall Edge and Bumpers Guards
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Wrapping these around a pole is a guarantee. If you want to wrap the pole completely 360 degrees, you may need multiples of these, depending on the thickness of the pole.
The "Column Guard" is already assembled. cut to allow for curved surface adhesion It looks great on steel columns, and the stripes can be carefully aligned for a thought-provoking effect. out of the installation
yes! Because the garage wall products are self-contained, GUEQUITLEX's wall guards are simple to install on nearly any smooth surface, including plaster, wood, metal, concrete, and so on. adhesive
I haven't tried to take them off yet, and the adhesive is quite strong. If you used a blow dryer on the adhesive, I'm sure it would come loose.
Selected User Reviews For Garage Wall Protector Foam Wall Column Guard for Parking Garages - Reflective Wall Edge Protector - 2 Pack Pole Guard - Wall Edge and Bumpers Guards
Because these forms pads were already sliced into 1/2 inch vertical sections, wrapping around the stanchion post in my garage was much easier. I used alcohol wipes on the metal before applying the adhesive to ensure that it had a clean surface to adhere to, but I'm not sure it was necessary. The adhesive on the back is very strong, and it appears to be holding up well in terms of humidity and heat. The foam padding is very firm and holds up well to impacts, saving the paint on my wife's vehicle's rear driver's side door. The yellow caution paint is very reflective and should catch the attention of anyone opening the door, even if it isn't because of the foam padding.
awesome. Although I didn't hang it on the wall, the design - They fit around pipes perfectly. We used these to keep people from hitting their heads in our parking garage. Instead of using the adhesive on the pads, I wrapped them in clean packing tape. But I need to remove them when I need to paint the pipes, so I'm doing it this way.
There is a lot of foam and it is highly reflective, but the adhesive is extremely sticky. Only one shot is available to you. It is impossible to remove it without destroying it once it has been put on. It almost sucked itself onto the pole as I was putting mine on. It was installed incorrectly, so I attempted to reset it, but there is no way I can do so without destroying it. I decided to leave it alone because it appears to work, even if it isn't particularly attractive. However, I do endorse the item.
These were required to wrap around support poles in a garage so that doors would not hit them. They appeared to be perfect in the picture, but when they arrived, they were flat and needed to be cut with an exacto knife to wrap. There were no lines to follow or cutting instructions, so it doesn't appear that this was their intention. I got it to work, and it's fine; it's not as perfect as the picture suggests, and I doubt anyone could do it as well as I did. Otherwise, if they had been designed to wrap around poles, I would have given them a perfect score in every category. Despite the fact that they've only been up for a week, the adhesive appears to be holding. They'd be ideal for use on a flat surface or in a corner.
With the sheets stacked three high, one sheet has 5 ribs from the 4th sheet to finish the circumference. In my installation, the fourth sheet (which has 16 "ribs") is used to fill the gaps at the back of the pole. There was one rib that wasn't used. br>br>Ian advised using rubbing alcohol as a pre-treatment. The suggestion of keeping things clean was excellent. br>br>If the sheet is placed more than once, the glue will become unmanageable and the rubber will be damaged. I'd recommend scribing a level line on the pole to aid in the placement of the first sheet. The bottom sheet was placed with the help of a level. Apply the sheet's middle rib to the pole and spread it out carefully. You'll be happy if you take the time to clean and level it. br>br>From start to finish, the installation takes 15 minutes. br>br>A three-sheet padded pole is enough to catch the doors of a 2019 Honda Civic Hatchback and my 2014 F-150 pickup. 150 (standard supercab that has been leveled but not raised). The bottom sheet's bottom edge is about 10" from the ground. br>br>I'll be purchasing a second kit to complete the other garage lally pole, which will cover the back doors: ) I was planning on doing two per pole at first, but three is the magic number for the variety of vehicles we could potentially park here (Honda Civic, CRV, Odyssey, and F150). br>br>At first, I'm very pleased, and I'm hoping for a long-term relationship.
It took only a few moments to set up. There's no need to be concerned about the metal post any longer.
It sticks very quickly, and once it's stuck, you won't be able to get it off! When I was trying to tape it to my garage's metal pool, I made a mistake and got my hands sticky. So exercise extreme caution. Before you remove the sheet, make sure you know exactly where you're going to put it.
My storage area is crisscrossed with pipes. On these pipes, it's easy to make a fool of yourself. This protective foam does a good job of protecting my head.
Related Products For Garage Wall Protector Foam Wall Column Guard for Parking Garages - Reflective Wall Edge Protector - 2 Pack Pole Guard - Wall Edge and Bumpers Guards
