Flarestar 6 Switch Pod/Panel with Control Overhead Electronic Relay System Circuit Control Toggle Box Waterproof Light for Wrangler JK JKU 2007-2018 LED Lights Bar Rock Lights
Score By Feature
OveReview Final Score
Product Description
Questions & Answers
Unless I am mistaken, I believe the far right switch is connected to the far left set of hot &amp cold Under the hood, there are ground terminals on the control box. There are two sets of + & In order to correspond with each switch, we create terminals On the switch panel, left is to right in the control box and right is to left in the switch box.
Almost any accessory that runs on 12V will work on this device.
The same issue plagued me as well. As it is attached to a hook to the left of center, it moves the whole thing to the right of center. Are you rigging up an effective mounting method that centers it and will hold it tight.
All the lights are on all the time.
Selected User Reviews For Flarestar 6 Switch Pod/Panel with Control Overhead Electronic Relay System Circuit Control Toggle Box Waterproof Light for Wrangler JK JKU 2007-2018 LED Lights Bar Rock Lights
Despite my attempt to align the switch panel of the 2012 JKU, the actual unit didn't line up nearly as well as it appeared on the website. There is a different brand on the picture they show, and the top part where the bracket is mounted does not have the angled bend. If you put this on, you can't use the center latch on the freedom panels. I had to remove the latch in order to put the tops back on, which wasn't a big deal, but it is still an inconvenience. Also, the 3M tape they use on the bottom is useless, as it doesn't stick close enough to the molding to fit. In the end, I modified the unit to get it to In order to secure the bottom end, I drilled a hole and fastened it with a bolt. Regarding the fuse box, it appears to be fine, although the fuse holders could have been made a bit better. They are not really fuse holders, but spade connectors that are soldered directly to the board and may or may not break off in the event of a fuse blowing. As far as the wiring harness itself goes, it looks good. If the switch panel didn't need to be modified to fit and I didn't have to remove my center latch, I would have given this a higher rating overall. The price point of this unit permits me to put up with some modifications I made, so I debated returning it for a more expensive one.
I wanted this item to work. I tried mounting it several different ways, but none of them worked. Housing was made of metal for a low price, but the paint was chipping apart during installation.
Trash would have been a better word. The question is, how much money would it have cost to have someone who speaks English write the installation instructions for you, or better yet, just put a link on the box directing users to someone who has already installed one of these? Next, I arranged the cables and mocked up all the parts so they would fit in the order the instructions call for them to be positioned so they would be long enough before securing them. In the relay box, the positive cable and the control cable are installed on the forward side, so the box cannot be installed flush against the computer as shown here. Various cables have been reworked to connect to the other side, while the relay box has been tightened. Although the directions show that the circuit breaker is to be mounted in the middle of the firewall, it was located at the end of the main positive You're in the right place to start having fun. During mounting the circuit breaker, the garbage chinese crimp pulled away from the main power wire. On closer inspection, there were not all of the strands that made it into the crimp, and there was not enough insulation removed to get a Now I'm faced with the dilemma of returning it and hoping one of my children will be worth enough to buy a good relay box and switch panel or recycling the junk Chinese cables and routing them correctly with a crimping that holds strong enough to hold There will be more updates once I figure out my next step.
I found the instructions to be very inadequate. I am impressed with the quality of this product. We're supposed to figure out how to install from a vendor's website, but why do they make us watch videos? I would like you to spend a few more minutes and create a full set of instructions that we will all be able to understand. Additionally, the socket head screws supplied will not work due to the tight fit at the top of the windshield. Ace Hardware had to be visited to get hex key An example would be screws with heads. It will be much easier to install your software if you follow those steps.
With this, I was able to control two electric lockers I installed on my 2013 JK sport. Although it has a poor installation guide, you can go to YouTube and find an install that has a different name and it will follow the same steps. One thing that disappoints me is that the labels on the switches are stupid and despite the fact that stickers come with it, I doubt you will be able to change the labels.
Installed in a few minutes without any problems. In a 6 spd JKU, feeding through the Pin connector through the firewall was the most difficult part. The ECU mounts on this and made it hard for a 14 JKU to fit perfectly. It is only held in by two of the three bolts, which I have no problem with. As a result, it would be advisable to replace the 3M tack that comes with the overhead unit, as it loses its sticky properties after.
The link is not working. I connected this item fully and followed all instructions as well as some YouTube videos, but it had not worked at all. A power cord cannot be found to supply power to the unit. The lights do not come on. There was no way to contact the seller through Amazon. It was a waste of time trying to wire I think that this would be a great product, but because it does not have power, I cannot buy it.
I had to rewire and loom the fuse and power wires that were not loomed Loomed the deadline. It was found that the wire in the loom had been damaged. A power outage was discovered after installation when we observed no power going to the switch panel from the control box. Diagnostics and wiring (total install time of 5 hours) verified the system was working fine.
The bracket that goes on the center freedom top latch is a POS with a locking mechanism. It is possible to see a small gap between the plastic windshield paneling and the switch panel.