Spectre Performance Air Intake Kit: High Performance, Desgined to Increase Horsepower and Torque: Fits 2011-2019 CHRYSLER/DODGE (300, 300C, Challenger, Charger) SPE-9028

A 2014 300C is now installed with it. Good to hear I consumed a decent amount of food. I found the parts to fit fairly well and that the instructions were good for this type of product.

All parts were included, and they were all I don't like this at all There are large gaps between the heat shield and the conical mount because the heat shield does not fit tightly to the chassis. It is likely that a lot of hot air will enter through those vents, so the air charge will be higher than normal. There is a draft on the flange of the conical adapter, which is injection molded. In other words, the conical is sliding It is obvious that this is a bad situation. My solution was to clean and etch the flange and the inside of the filer to resolve the issue. In order to prevent the filter from sliding, I placed a light tac adhesive on the flange.

On the other hand, the mounting grommet for the heat shield does not fit. When it is compressed, it could pass through the opening on the vehicle chassis even though it is too loose. As well, the bolt included with the kit isn't long enough to use the washer included with it. I'm waiting to see if it causes any issues at all before making additional changes to the one in the car because it's impossible to take all of it apart. In general, the performance notes are A noticeable improvement has been made in throttle response. There is a low probability of this Torque is also improved at the end of the shaft. There is probably a 5-percent gain in HP There are no obvious differences after 4000RPM, but there is a difference after 8. There is excellent sound up to 6000RPM, but there is audible noise at full throttle, so don't forget to get If the engine is running at WOT at 6000 RPM, it purrs and chatters a lot. Since the only time this happens is if you beat the crap out of it, I don't mind.

Aspen Escobar

| Feb 24, 2021

This intake is great for the money, it adds some throttle response and it's not overly expensive, but there's one fatal flaw described in other reviews before I bought the intake and sure enough, after using it for a short period of time, I too experienced it. There is no matter how tight you clamp the filter it will just pop off of the plastic piece to which it is attached. For the consumer to be sure that the filter does not come off, it must be modified at their end. The rest of the unit is made of metal and rubber with metal hose clamps, so I'm impressed with the quality of the materials (except for the one plastic piece). Although the instructions are hard to follow, they are just a few black and white images, and I could not find anything online on the subject, but I was still able to install it. is fitted with a cutout for the IAT sensor, so you will not get any engine error Furthermore, I installed it on an older 320 charger that looked a little different from the two newer ones. However, it is still possible (pictures shown) with the only difference being that the breather hose will be on the left and not the right. Based on the pictures, repositioning the hose should be easy. I'll route it over a 3 or newer. Although I'm generally impressed with this product, I feel that due to one major flaw which could seriously affect an engine if not addressed promptly, it does not merit a full five-star rating. Last but not least, this filter claims to be legal in 50 states. The only issue I ran into was finding a CARB OE # for this intake, so I don't think it will pass a smog check in California. It is recommended to keep your airbox if you are in California.

Wrenley Lynch

| Sep 25, 2020

We received this during the first few days of January My order arrived within 24 hours of the time I placed it. I am not quite sure how that worked, but I have For those of you frustrated about the lack of color instructions, here is a suggestion. To find out more, consult the manufacturer's website. Oh my god. Please refer to the instructions for color. I CAN'T FIND AN EXPLANATION. Scratches on the tubes of those who have them. That's how it turned out. I believe they came factory installed on the car because they are so smooth. You can view photos by clicking here. You won't know what to do with yourself after reading this review. The gains in HP look great. I can't wait to put them to the test.

Aldo Humphrey

| Jun 06, 2021

The money you spent for that was a complete waste. When I installed it two days ago, the filter fell off the smooth rim it was supposed to tighten against twice. As a result, my horsepower increased, and I don't have any filter to reduce Although I have tightened up the bracket, the filter still starts to shimmy off the end when vibration starts. Would it be possible to make threads for securing the filter to the rim of the plastic box? The next step will be to sand the outside of the plastic rim the filter goes over and apply barge cement to it. This hardware has little credibility, and I'm setting it aside to remove it shortly. Worrying about whether or not road debris is getting into the engine just because it will not stay coupled is too stressful for me. Similarly, as many other people have noted, the instructions are pretty bad as well.

Harlee Delgado

| Oct 11, 2020

product the tubing is thin, and it heats up pretty quickly, but getting the stock filter to suck in more air is a huge improvement. Make sure that you remove your headlight light outlet if you wish to have cooler air. The CAI is able to get cold air right into the system. These are a great addition to any engine and are a must-have.

Khalil Frank

| Feb 09, 2021

Comments about the air filter falling off were all from people who experienced the same issue. The answer is yes. The filter has a HUGE defect. You will have to sand the coupler, use high-quality bonding cement, and use a socket wrench to tighten the fastening band down to keep the filter in place. had driven around for several hours before realizing what had happened, pulling whatever was in my engine. There was also a part that was going bad on the IAT sensor. The sensor does not align correctly, it does not work, and it stays in the wrong place. As a result, I had to shape Buy an item of higher quality.

Lee Newton

| Sep 10, 2020

When it comes to the price, you get what you pay for. There are no labels on the parts, and the instructions are unsatisfactory. You can install it a little more easily if you've seen a video of it being done. Though you'll need some basic knowledge to get it together, you shouldn't have any difficulties doing so. After a bit of struggling, you can use the grommet for the air sensor, but it is kind of a pain. In addition, if you rough up the lip of the adapter housing that clamps onto the air filter, it will not stay in place. If you don't have sand paper, you can use a Dremel. Think of new ways to express yourself.

Boden Parrish

| Oct 09, 2020