GM Genuine Parts 15281541 Automatic Transmission Fluid Fill Tube, Black

$ 30.76

Score By Feature

Based on 156 ratings

Easy to assemble

9.50

Value for money

9.60

Easy to clean

9.50

Sturdiness

9.80

OveReview Final Score

How Our Score Is Calculated

Product Description

Adecco GM Original Equipment (OE) may have been part of some GM Genuine Parts in the past

All Genuine General Motors Parts are designed, engineered and tested by GM to rigorous standards, and are backed by the support of

Engineers at GM design and validate Original Equipment parts specifically for your Chevrolet, Buick, GMC or Cadillac automobile

A new generation of materials and technologies is continuously incorporated into design for production and service parts at GM

Questions & Answers

Would this be compatible with the Hummer H3 from 2006? The website says it fits on the AC Delco site. What does that mean?

It is true. I purchased it and installed it on my Hummer H3.

What do I need to do to install my 2005 GMC Canyon?

On my 2005 GMC Canyon, everything went together as it should

Is there a seal on this tube?

Toward the end of the transmission, the tube is sealed with a rubber gasket. Purchasing the tube separately is required as it does not come with it.

When the tupe is pulled out, does it just come out of the seal? What will happen if fluid leaks out and needs to be replaced?

Using a wrench, remove the nut on the Put tube on a pulley and Only a small amount of fluid is lost. I don't think it's necessary to replace it.

Selected User Reviews For GM Genuine Parts 15281541 Automatic Transmission Fluid Fill Tube, Black

The 2006 Hummer H3 was easy to install

5/5

When I was doing some maintenance on my truck, I found this one broken, so I picked it My 2006 Hummer H3 was able to fit it perfectly. You only need to remove the nut that holds the tube to the engine block and pull this tube out. There is a rubber washer at the bottom of the tranny fluid reservoir which it slides into and out of. It's easy to replace this one simply by pulling up the old one, installing the new one, and then reattaching the nut and tube. I had no fluid spill so had to replace it since there was no fluid spill. The rubber washer I picked up was also in case, but I did not replace it since it looks like the old one is still fine.

Zion Stuart

| Aug 23, 2020

The following installation recommendation is given

5/5

I was very pleased with the quality and fit of this part. It is not necessary to make any changes. Make sure to order a new rubber seal or grommet for the installation and plan to service the transmission at the time of installation. There were several pieces of the factory seal that fell into the pan when I was installing it. It is impossible to prevent this from happening by design. There is a transmission filter required on the Hummer H3 There are 5 quarts of Dextron VI, along with the gasket set. The pan bolts should be torqued back at 9 foot-pounds or 180 inch pounds in a crisscross.

Seth Booth

| Nov 09, 2020

I fitted my 2007 Hummer H3 with this product

5/5

After spending about 15 minutes installing the new tube after taking out the old one, it took about 2 minutes to take it out. On the tube there were some new bottom seals to be installed.

Blake Mullen

| Aug 02, 2020

You can do it very easily! My husband and I did this the easiest thing we have ever done while working on a vehicle

5/5

Zyair Bautista

| Feb 10, 2021

I was in heaven

5/5

It was perfect. I was in heaven. It was perfect. It does not have a YouTube video, so you will have to figure it out on your own. To make it work, I had to put the light beneath the Hummer and point it upward. This allowed me to see where the thing jams in from top to bottom,.

Keaton WESTON

| Nov 11, 2020

Parts from GM of high quality

5/5

You look good in it.